Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Features:
Door opening electronics without extra power supply • Indoor unit allows outdoor video surveillance (30 sec) • Intercom feature • 4" monitor in the indoor unit • Adjustable ringer and speech volume • Adjustable brightness
and contrast• Indoor unit can be positioned horizontally or mounted on the wall
accessories:
1. Monitor
2. Speaker
3. Microphone
4. Power on LED
5. Door open button
6. Monitor button
7. Call button
8. Intercom start button
9. Contrast control
10. Brightness
11. Adaptor socket
12. Speech volume
13. Ringer volume
14. Connection panel connector
15. Audio phone connector
16. Jumper to select one or more indoor video units
17. Jumper for door opener
18. Mounting frame
19. Connection panel
20. Camera
21. Infra-red LED's
22. Speaker
23. Ringer button
24. Microphone
25. Indoor unit connector
26. Door opening device connector
usage, installation and Features
Basic features
Use the cable to connect the connection panel connector (14) at the back of the indoor unit and the connection panel. Then connect
the included wire to the connectors at the connection panel, observing the color codes:
1R (red)
Power (+) (12V)
2W (white)
Power (-) GND
3Y (yellow)
Video signal
4B (black)
Voice and control signal
Connect the two units (recommended cable: shorter than 50 m, 4 x 0.3 mm
The door phone can control door opening devices with the following parameters: 12V DC/500mA. The door opening device can be
connected to the external unit (26). This should always be performed by a technician.
Ways to connect the door opening device:
Without external power supply: page 8., figure 1.
With external power supply: page 8., figure 2.
Finally, connect the adaptor to the device's power in socket (11), then plug in the adaptor.
It is recommended to position both units at a comfortable height in order to get the best view of your visitor on the indoor unit's
display.
connecting multiple units
The device can be used to connect up to two outdoor units, multiple indoor units, and a handheld speaker. These schemes can be set up in the following way:
Connecting an additional handheld speaker (DPV 3T): page 8., figure 3.
Connecting 1 outdoor unit and multiple indoor units: page 8., figure 4.
Connecting 2 outdoor units and multiple indoor units: page 8., figure 5.
Functions
Your visitor presses the call button on the outdoor unit. The indoor unit emits a voice signal, and the image from the outdoor camera is displayed. If you wish to talk to the caller, press the TALK button. If you do not press the TALK button, the display will switch off
automatically after 30 seconds. If a door opening circuit is connected, you can open the door by pressing the UNLOCK button. To terminate the call, you can press the TALK button again: the audio and video connection will end.
You can view the image from the outdoor camera for 30 seconds by pressing the MONITOR button. If two outdoor units are connected, pressing the MONITOR button will display the image from the first outdoor unit; pressing the button again will display the image
from the second outdoor unit. Pressing the button a third time turns off the display.
The display's image can be adjusted using the controls for contrast (9) and brightness (10) behind the indoor unit's sliding door. The controls for adjusting the ringer volume (13) and voice volume (12) are on the device's back, and can be turned with a
screwdriver.
If there are multiple indoor units in the system, you can start a call by pressing the INTERCOM button. The other indoor devices will then emit a voice signal; pressing the TALK button on them will answer the call.
selecting the ringtone
In the default mode, press and hold the UNLOCK button for 2 seconds. The door phone will play the currently selected ringtone. You can step through the 15 available ringtones by pressing the UNLOCK button again. If you do not press any button for approximately
15 seconds the last played ringtone will be stored.
Warnings
• When finding the place of the devices, make sure they will not be exposed to vibration.
• Do not place the devices close to a magnetic field or electric appliances.
• Do not expose the devices to direct sunlight, and mount them in a location where they are shielded from water.
• Keep away from ammonia and other harmful gases.
• Make sure to lead the cable in places where it will not be damaged.
• If you do not use the device for a long time, unplug the adaptors.
• Thin cables can cause loss of audio quality.
• Never disassemble the device; consult a technician if repair is needed.
• Clean with a soft, dry cloth; do not use aggressive detergents.
• If the power cord is damaged, unplug the device immediately, and consult a technician.
accessories
• Indoor unit (see below for parameters) • Outdoor unit (see below for parameters) • Network adaptor - 15 V/800 mA • Mounted telephone wire – 15 cm
technical ParaMeters
Indoor unit:
Power supply: 230 V/15 V 800 mA
Power consumption during operation (default mode): 15 W (0.5 W)
Image resolution: 300 TV rows
Dimensions: 230 mm x 188 mm x 47 mm
Operating temperature (indoor unit): -15 °C – +50 °C
GB
1
4
3
13
14
15
16
17
12
11
cable).
2
Outdoor unit:
Power supply: 10~12 V 150 mA
Power consumption during operation: 2 W
Image resolution: 420 TV rows
Minimum light needed: 0.1 Lux (at 0.3 m)
Outdoor unit dimensions: 127 mm x 97 mm x 38 mm
Operating temperature: -15°C – +50°C
21
2
20
5
22
6
23
24
7
8
9
10
25
19
26
18
2
video door phone
Werbung
