Hunter 99117 Bedienungsanleitung

English
Installation
Before installing the
Remove the canopy. If uncertain
Universal Remote Control
how to remove it, reference the fan's
Receiver, use the pull chains
owner's manual. Be sure that all wiring
to set the fan speed to HIGH connections are completed as per the
and the light to ON. Be fan's owner's manual before installing
sure power is OFF before the receiver.
proceeding with installation.
Maintenance
Battery
Door
Phillips
Head
Screw
INSTALLING OR CHANGING THE Use the pull-chain switch on
BATTERY the fan to set the fan speed
To access the battery compartment to the HIGH position before
remove the small Phillips head screw operation.
that secures the battery door to the
transmitter assembly. The battery
should be installed with the positive
(+) side up. Replace with a CR2032
battery when necessary.
Ceiling Fan
Remote Control
Receiver Receiver
Canopy Canopy
Choose the hanging system that most closely resembles the one used by your fan and place the receiver as shown.
Operation
Fan Off
High
Medium
Low
The remote transmitter should
The Fan Off button only turns the fan
already be paired to the receiver and
off. To turn the fan on, press one of
ready to use.
the fan speed buttons.
Note: If your need to pair (or unpair) ooo High
your remote, turn fan power off and
oo
Medium
back on at the wall switch. Within
o
3 minutes, press and hold both the Low
Fan Off button and the High button
for 4 seconds to pair the remote. To
prevent faulty operation, please
ensure all other ceiling fans within
range are turned off at the wall
switch while pairing or unpairing.
MB017 • 11/04/15 • © 2015 Hunter Fan Company
Remote Control Model: 99117
Ratings: 240 VAC, 1A Max
Read and Save These Instructions
WARNING! Risk of Electrical Shock
To avoid possible electrical shock, before wiring fan, disconnect power by
turning off the power mains both to the outlet box and to its associated
wall switch location.
Compliance
• This equipment has been tested and complies with: IEC 60730-1 and
EN 60730-1.
For low profile fans, secure the receiver
to the ceiling bracket with a cable tie.
Cable Tie
Cable Tie
Ceiling
Ceiling
Receiver
Receiver
Plate Plate
Receiver Receiver
Receiver Receiver
Canopy
Canopy
Canopy Canopy
Cradle
Light
Quickly press the Light button to turn Choose the wall mount that fits your
the lights off and on. Hold the Light wall switch. Each wall mount has two
button to raise and dim the light level. posts to mount your remote control
when not in use.
Dimming Mode: To enable dimming,
you must first set your remote to
Dimming Mode. To toggle Dimming
Mode on or off, hold down the Fan
Off button while pressing the Light
button twice.
www.HunterFanInternational.com
• All wiring must be in accordance with national and local electrical codes. If
you are unfamiliar with wiring, you should use a qualified electrician.
• In Australia, national laws require a qualified electrician to install this
control in accordance with national and local codes.
• To avoid over heating and possible damage to other equipment, do not
install to control a receptacle, fluorescent light fixture, motor operated
appliance, or transformer-supplied appliance.
Use only to control one ceiling fan.
For use only with electrically reversible ceiling fans rated at 1.0 A or less.
Not for use with shaded-pole or nonreversible motors. Not recom-
mended for use with the Hunter Original
Ceiling
Ceiling
Hanger Bracket
Bracket Bracket
Fan Body Fan Body
Connect Plugs
Fan
Make wire connections using the 4-pin plugs coming from
the receiver, fan, and hanger bracket as shown. Connect
the female plug from the receiver to the male plug from the
hanger bracket. Connect the male plug from the receiver to
the female plug from the fan.
Safe-Exit Troubleshooting
The Safe-Exit Program gives you Fan will not start
about thirty seconds of light when
• Make sure the power switch is on.
you turn the lights off to exit the
• Make sure the battery is working.
room before the lights go out. To
• Make sure that the transmitter and
use Safe-Exit:
receiver are paired.
• Press the Fan Off button for at
• Check wire connections inside of
least three seconds to initiate
the canopy.
the Safe-Exit Mode.
Remote control of fan is erratic
• The lights will flash for visual
• Make sure the battery is installed
confirmation.
correctly.
• The lights will stay on 50%
• Install a fresh battery.
brightness for 15 seconds and
then begin to dim. After a total
Transmitter only works when held
of 30 seconds, the lights will be
at close range
completely off.
• Change battery.
Note: For CFL lighting, the lights
Lights do not dim
will stay on 100% brightness
• Toggle the Dimming Mode on:
for 30 seconds. After a total of
Hold down the Fan Off button while
30 seconds, the lights will be
pressing the Light button twice. If
completely off.
the problem is not corrected, repeat
the process up to three times.
CFL bulbs flicker
• Toggle the Dimming Mode off:
Hold down the Fan Off button while
pressing the Light button twice. If
the problem is not corrected, repeat
the process up to three times.
®
.
Connect Plugs
Receiver