RIDGID 580 Gebrauchsanleitung Seite 2

OPERATING INSTRUCTIONS
Technical data.
Type: 580
Power input: 2200 Watts
Speed: 3400/min
Blade size: 350 x 25.4 mm
Weight: 17 Kg
Max. capacity.
90°: 4 1/4" x 6 1/2" (107mm x 165mm)
45°: 4 1/4" x 4" (107mm x 100mm)
Standard equipment.
Abrasive disc for metal.
Wrench.
Safety Instructions.
Warning: When using electric tools, basic safety
precautions should always be followed to reduce
the risk of fire, electric shock and personal injury.
Read these and the accompanying safety instruc-
tions before attempting to operate this product.
Caution: Before plugging unit into the power
socket, check the following :
• Voltage: The voltage on the rating plate
must be the same as that of the supply.
• Switch: The machine should be switched
off (switch lever in position "O").
• Tool: Use appropriate RIDGID Abrasive Disc
for material.Abrasive disc: Inspect the disc
before use. Do not use damaged, worn or
otherwise defective discs. Ensure the disc is
correctly mounted before use and run the tool
at no load for 5 to 10 seconds. Stop immedi-
ately if there is considerable vibration or an
other defect is detected.
The use of incorrect abrasive discs will reduce the
cutting capacity and may cause serious accidents
or damage to the machine.
Additional safety precautions for
the abrasive saw.
1. Always clamp the work firmly against
the fence.
2. Raise the disc from the cut before
releasing the trigger switch.
3. Allow motor to reach full speed before
cutting.
4. Verify that the electric power outlet socket
has a ground connection and that it is pro-
tected by a 10A fuse and by a residual cur-
rent circuit breaker with a trip current of
30mA.
5. Use only RIDGID abrasive saw discs with a
speed rating at least as high as the R.P.M.
specified on the nameplate.
6. Carry the tool by the handle for transport.
7. Keep the power cord away from the cutter
blade at all times to avoid damage and the risk
of electrical shock.
8. Wear eye protection.
9. Wear respiratory protection
10.Check that guard operates correctly before
plugging in the unit. Never operate the ma-
chine without the guard in place.
Operation.
The tool is equipped with an approved three-
conductor cord and three prong plug to fit a
grounded socket outlet. The green and yellow
conductor in the cord is the grounding wire.
Never connect this wire to a live terminal.
ON/OFF switch trigger.
(see fig.1) Push in mechanical lock for ON/OFF
switch and pull on trigger to start motor. Release
trigger to stop motor.
IMPORTANT
The RIDGID abrasive disc will give long life if
certain fundamental rules are followed :
• Do not force the disc into the material to be
cut.
• Only cut material within the specified
capacity for the disc.
• Let the machine reach full speed before
starting to cut.
• NEVER stop and restart with the disc in
contact with the material.
• Clamp the material correctly and ensure
that it is centred relative to the disc.
• Clamp the material to give the smallest
cutting area to reduce heating of the disc.
Damage to the disc caused by a failure to follow
these rules is not covered by the Ridgid warranty.
Cutting different shapes.
(see fig. 2)
Note: Remove plug before adjusting fence guide.
90° cuts.
Set fence guide for 90° cuts making sure that the
workpiece is centred relative to the disc and
clamp it between the vice plate and fence.
45° (or other angle) cuts.
Set fence guide to desired angle and re-tighten
the two bolts. Centre workpiece and clamp it
between vice plate and fence.
The quick set handle can be used to rapidly clamp
and re-clamp the same sized workpieces (see fig.
3).
Maintenance and inspection.
CAUTION: Before starting any kind of adjustment
or maintenance on the machine always remove
the mains plug from the socket.
Carbon brushes.
Replace brushes when they become worn (6mm.
minimum length). Only genuine RIDGID replace-
ment brushes should be used. Remove the
mains plug from the socket. Remove the ventila-
tor/brush cap cover. Unscrew the brush holder
cap and remove the brushes without damaging
the brush holders. Replace the brushes and
screw back the brush holder cap. Check for brush
sparking through the air inlet slots. If the spark-
ing is excessive switch the machine off immedi-
ately and return the machine to a RIDGID author-
ised service centre.
Changing Abrasive Discs.
(see figs. 4 and 5)
1. Remove the power cord plug from the socket.
2. Push the safety cover to the rear position and
lock in position.
3. Press the spindle lock and place the wrench
on the arbor bolt. Unscrew the bolt and re-
move the disc carefully.
4. Slide the new disc onto the arbor shaft.
5. Replace the outer flange and arbor bolt and
tighten it securely.
Inspection.
Periodically inspect the tightness of all screws
and re-tighten any that are loose. Loose screws
may damage the tool or cause serious accidents.
Any other adjustments or repairs should only be
made by RIDGID authorised service centres.