Grohe Minta series Montageanleitung Seite 5

NZ
AUS
Application
• for kitchen
Can be used in conjunction with:
• Pressurised storage heaters
• Thermally controlled instantaneous heaters
• Hydraulically controlled instantaneous heaters
Operation with unpressurised storage heaters (= open water
heaters) is not possible.
Technical data
• Flow pressure
- min.
- recommended
• Operating pressure
• Test pressure
If static pressure is greater than 5 bar, fit pressure reducer.
Avoid major pressure differences between cold and hot water
supply.
• Flow rate at 3 bar flow pressure:
• Temperature:
- hot water inlet
- recommended (energy saving)
• Water connection:
• Clamping length
Note:
All GROHE single-hole mixers with pull-out sprays are
equipped with non-return valves.
Installation
Flush piping system prior and after installation of fitting
thoroughly (Consider EN 806)!
This product must be installed in conformance with local codes
e.g. AS/NZS 3500 series of standard!
Prepare sink mixer
Refer to the dimensional drawing on fold-out page I.
Mount sink mixer, see fold-out page II, Fig. [1].
1. Fit escutcheon (A) and O-Ring (A1).
2. Insert mixer into sink. Feed the connection hoses separately
through the sink.
3. Fit support plate (B), if necessary and washer (C). Connect
nut (D) with tube (E). To do this, insert installation tool (G)
into tube (E) and turn installation tool (G) clockwise to fasten
mixer.
(Tube may also have to be turned with an 21mm open ended
spanner.)
Note:
If the support plate (B) is omitted, the clamping length can be
increased by 15mm.
Connect sink mixer, see Figs. [1] and [2].
Connect the spray hose (H), see Figs. [3] to [5].
1. Feed the spray hose (H) through the spout (J), see Fig. [3].
2. Feed the spray hose (H) through the mixer body from above
and fit spout (J) so that it snaps into place, see Fig. [4a]
or [4b].
3. Connect rinsing spray (K) to spray hose (H) without using
any additional seals.
4. Push spring (L) onto spray hose (H) from below, see Fig. [5].
5. Screw snap coupling (M) with non-return valve (N) on the
end of the spray hose (H) and tighten by hand.
6. Pull the sleeve (M1) of the snap coupling (M) downwards
and fit to the union (Q).
To ensure that the rinsing spray (K) is correctly seated when
inserted, lug (K1) on the rinsing spray must engage into spout
groove (J1), see Fig. [4a] or [4b].
Open cold and hot water supply and check connections
for leakage!
Check fitting for correct operation, see Figs. [6a] or [6b].
Flow rate limiter
0.5 bar
This mixer is fitted with a flow rate limiter, permitting an
1 - 5 bar
infinitely variable individual reduction of the flow rate.
max. 10 bar
The highest possible flow rate is set by the factory before
16 bar despatch.
The use of flow rate limiters in combination with hydraulic
instantaneous water heaters is not recommended.
To activate see "Replacing the cartridge" point 1 to 3,
Figs. [7] and [8].
approx. 8 l/min
(max.) 80 °C
60 °C
cold - right
Maintenance
hot - left
Inspect and clean all parts, replace as necessary and grease
max. 60mm
with special grease.
Shut off cold and hot water supply!
I. Replacing the cartridge, see Fig. [8].
1. Lever out plug (O).
2. Remove set screw (P) using a 3mm socket spanner and pull
off lever (R).
3. Pull off cap (S).
4. Remove screws (T) and detach complete cartridge (U).
5. Replace the complete cartridge (U).
Assemble in reverse order.
Observe the correct installation position!
Make sure that the cartridge seals engage in the grooves on
the housing. Fit screws (T) and tighten evenly and
alternately.
II. Non-return valve, see Fig. [9].
1. Unscrew non-return valve body (N).
2. Unmount non-return valve (N1).
Assemble in reverse order.
Replacement parts, see fold-out page I ( * = special
accessories).
Care
For directions on the care of this mixer, please refer to the
accompanying Care Instructions.
2