CMi C-ELS-2500 Originalbetriebsanleitung Seite 18

Laubblaeser_Elektro_302137.book Seite 18 Freitag, 1. Juli 2016 12:28 12
GB
• Unsuitable material;
• Insufficient maintenance.
You can reduce the risks considerably by following
the tips below:
– Maintain the device in accordance with the
instructions in the operating instructions.
– Avoid working at low temperatures.
– When it is cold, make sure your body and your
hands, in particular, are kept warm.
– Take regular breaks and move your hands at the
same time to promote circulation.
Electrical safety
• The device may only be connected to a socket
that is correctly installed and grounded.
• The fuse must be a residual current circuit-
breaker with a measured residual current of no
more than 30 mA.
• Make sure that the power supply corresponds
with the connection specifications of the device
before it is connected.
• The tool may only be used within the specified
limitations for voltage and power (see type
plate).
• Do not touch the mains plug with wet hands!
Always pull out the mains plug at the plug and
not by the cable.
• Do not bend, crush, pull or drive over the power
cable, protect from sharp edges, oil and heat.
• Do not lift the device using the cable or use the
cable for purposes other than intended.
• Check the plug and cable before each use.
• If the power cable is damaged immediately dis-
connect the plug. Never use the device if the
power cable is damaged.
• If the device is not in use make sure the plug is
pulled out.
• Make sure that the device is switched off before
plugging in the mains cable.
• Make sure that the device is switched off before
unplugging it.
• Disconnect the power supply before transport-
ing the device.
Device-specific safety instructions
• When working with the device, always maintain
a safe distance and natural body position.
• Always hold the device firmly in both hands.
• Before starting to work, check the working area
for animals and objects. Remove all objects that
may be slung away or become jammed in the
cutting tool.
• Do not attempt to remove materials to be vacu-
umed or to hold material already vacuumed
when the motor is running. Only remove any
jammed material to be vacuumed when the
device is switched off.
• No other persons or animals may be present
within an area of 15 m around the vacuuming
area, as they may otherwise by injured by
objects being slung away.
• Only work in good light and vision conditions.
• Do not work above head height! Do not lean for-
ward or back!
18
• The operator must wear tightly fitting clothing.
Avoid wearing loose clothing. Wear sturdy shoes
and long trousers.
• Take care when walking backwards. Danger of
stumbling!
• Never work in the rain.
• Vacuuming, blowing of heavy materials such as
metal, stones, branches, fir cones or broken
glass is expressly forbidden.
• Keep all parts of your body away from the vac-
uum opening.
• When working with the device, ensure that there
is sufficient lighting.
• Always wear the required personal protective
equipment (► Personal safety equipment –
p. 19)
• Be careful of the dust you have raised and flying
objects. Especially dangerous is the rebound
effect on walls or walls of houses.
• Do not direct the device at people or animals
when vacuuming or blowing.
• Before starting to blow, loosen foreign bodies
with a rake or broom.
• The machine may only be operated during sen-
sible hours – not too early in the morning or too
late in the evening, as it may disturb other peo-
ple.
• The times listed by the local authorities must be
adhered to.
• The whole blower nozzle piece must be used so
that the airstream can work close to the ground.
• Heed children, pets, open windows, and blow
the foreign bodies safely away.
• Remember that moving parts may also be
located behind ventilation and venting slots.
• Symbols which are on your device may not be
removed or covered. Notes on the device which
are no longer legible must be replaced immedi-
ately.
Be careful when handling the device! Ob-
serve all safety instructions in the instruc-
tions for use!
Read the instructions for use before use!
Do not subject the device to a humid envi-
ronment!
Maintain a safety distance!
Risk of injury due to flying parts!
Unplug the mains plug before performing
any maintenance!
Risk of injury caused by rotating machine
parts!
Risk of injury caused by rotating machine
parts!