VibroShaper VIBROLEGS Gebrauchsanleitung Seite 7

REMOTE CONTROL BUTTONS (Figure 3)
Power button: Press this button to turn the unit ON or OFF.
Start/Stop: Press this button to start with your chosen settings. When the device is in operation, press this
button to stop it.
Time -: Time -: Reduces the time. The pre-set time is 10 minutes, divided into 10 levels. Press this button to
reduce the time.
Time +: +: Increases the time. Press this button to increase the time. The maximum possible time is 10
minutes.
Speed +: Increases the speed. The speed can be manually set from 1 to 10. Press this button to increase
the speed while the device is running.
Speed -: Reduces the speed. The speed can be manually set from 1 to 10. Press this button to reduce the
speed while the device is running.
Button (manual mode): When you press this button, „H0" appears on the display. In this mode, the oscillation
and massage functions run continuously, the speed is customizable. In standby mode, you can adjust the time but
not the speed. Once the device has been put into operation, you can adjust the speed but not the time.
Program Button: You start the automatic mode with this button. By pressing repeatedly, you can switch
Figure 3
between the programs „P1", „P2" and „P3". With „P1" the acupressure heads are deactivated and only the
oscillation is activated, with the speed being adjustable. In the programs „P2" and „P3" the massage function and oscillation are
active, and the device runs through a program with pre-set speed levels. You cannot change the time or speed in either of these
programs. Note: By pressing the P button on the device multiple times, you can also switch to manual mode H0.
The remote control has a range of 2.5 metres. For optimum signal transmission, make sure that there are no obstacles
between the device and the remote control, and point the remote control at the infrared receiver on the device.
Important notes on operation:
• You can select the P mode (Auto Program) after switching on the foot massager; press
only start M mode after activating the device.
• Stop the appliance by first pressing
massage.
• In manual mode, you can set the time before the massage starts and adjust the speed during the massage.
• In P3 mode, you can set the time before operation starts, and adjust the speed during operation.
• Note: In program P1, the rotating acupressure heads will stop as soon as you place your feet on the device. This is no defect.
Table 1: Program overview of P1, P2, P3 and manual mode:
Oscillation only
STANDARD TIME 10 MINUTES TOTAL
1st minute
2nd minute
3rd minute
4th minute
5th minute
6th minute
7th minute
8th minute
9th minute
10th minute
. Then switch off the device with the power button
P1
AUTOMATIC PROGRAM P2
FUNCTION
Oscillation only
Oscillation and acupressure
Oscillation only
Oscillation and acupressure
Oscillation only
Oscillation and acupressure
Oscillation only
Oscillation and acupressure
Oscillation only
Oscillation and acupressure
to activate the appliance. You can
or press again to continue the
Manual operation
SPEED RANGE
(CHANGES PER SECOND,
TOTAL 60 SECONDS)
1, 1, 2, 3, 4,
5, 6, 7, 8, 9,
10, 9, 8, 8, 9,
9, 10, 10, 9, 8,
9, 10, 9, 8, 8,
9, 10, 10, 9, 8,
8, 9, 10, 10, 9,
8, 8, 9, 10, 10,
9, 8, 8, 9, 10,
10, 9, 8, 8, 7,
7, 6, 6, 5, 4,
3, 2, 1, 0, 0.
7