Werbung
Quicklinks
INSTRUCTION MANUAL I MONTAGEANLEITUNG
SPECIFICATION
Wing span approx
: 25 in. (640mm)
Length approx
: 17.3 in. (440mm)
: 150 Watt
Electric motor
Servo
: 21x17x10mm (x2)
Battery
: 1500Mah
Drill
holes using the stated
0)
(in this case
l 5
mm
·
Use epoxy g lue
Locher bohren mit dem onge
1.5 mm)
gebenen Bohrer (hier
Epoxy-Klebstotf verwenden
DELTA ROCKET
RADIO CONTROL MODEL
n
.
Tok e p articular c o r e here
Apply cyano glue
n
Hier besonders outpassen
Eii
Sekundenkleber outtrogen
TECHNISCHE OATEN
Spanweiter
:640mm
Lange
:440mm
Elektroantrieb
: 150Watt
Servo
: 21x17x10mm (x2)
: 1500Mah
Akku
C hec k durin g assembly that t hese
p o rt s mo v e free ly, witho ut b indi ng
Et
film carefully
Ass
mbl
e
left and rig ht
T hese p orts m u st be
e
sides the same
way
I]
Schrortierte
Stell en.
Besponnfolie vorsichtig
entfernen
Linke und rechte Serte
wird
gleichermoBen
zusommengeboul
.
Not included.
pu r chased separately
Wcihrend
des
Zusommenbous
.
immer prufen. ob sich die Teile
ouch relbungslos bewegen !assen
Nicht entholten. Teile mi.Jssen
seporot gekoutt werden.
Werbung
Verwandte Anleitungen für VQ Delta Rocket
Inhaltszusammenfassung für VQ Delta Rocket
- Seite 1 DELTA ROCKET RADIO CONTROL MODEL INSTRUCTION MANUAL I MONTAGEANLEITUNG SPECIFICATION TECHNISCHE OATEN Spanweiter :640mm Wing span approx : 25 in. (640mm) Lange :440mm Length approx : 17.3 in. (440mm) Elektroantrieb : 150Watt : 150 Watt Electric motor Servo : 21x17x10mm (x2)
-
Seite 2: Wing Installation
4x32mm nylon bolt I Fliiche ..4x20mm plastic screw. Unteran sicht BOTTOM- VIEW... -
Seite 3: Rudder Installation
RUDDER INSTALLATION I Installation Le itwe rk Cut away only the film both the left and right side* Trial fit each part before gluing . Be certain that there are no gaps. If the parts will join, but with a gaps. sand or trim the parts a little at a time until the parts meet exactly with no gaps. -
Seite 4: Servo & Control Horn I Servoeinbau
BOTTOM VIEW Unteransicht BRUSLESS MOTOR Using a motor mounting as a template. mark the plywood where the four holes are to be drilled (2). Remove the motor and drill a 3132"(2.Smm) hole through the plywood at each of the four marks marked . Again, put the motor in place and secure it using four 2.5x1 Omm screws (not included) Brushlessmotor (outside) - Seite 5 Securely install the receiver and power pack, ensuring they will not come loose or rattle during flight. Never fly before checking the Cg's required position. The recommended C.G (Center of Gravity) location for the Delta Rocket is 5.7"-5.9"(145 - 150mm) Adjust the location of the battery pack as required to achieve this C.G location.
- Seite 6 Ruderaus schlag CONTRO L SURFAC E HOhenruderausschlag 3/32"(2.Smm) the Elevator +2.Smm before take off _____ WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of control! and cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough. Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.