Technical Data; Accessories - Niko-Servodan 41-350 Gebrauchsanweisung

Orientation lighting:
In case the detector hasn't registered any activity, the off delay
has ran out and there is insuffi cient daylight, the lighting is
dimmed to the "Level 2" setting. After the "Time 2" preset time,
the lighting switches off completely.

Technical data

Input:
Supply voltage ...........................230 V AC 50 Hz +/- 10%
Power consumption (standby)...0.3 W (without light fi ttings).
øL .............................................L
1
øN ..............................................N
Pushbutton power switch:
øL .............................................
1
ø .............................................
Output:
DALI/DSI Bus 1 .........................Load max. 30 mA or
–
ø D1&2 ...................................0 V DC and communication
ø +D1 .........................................+15 V DC +/- 20% and
DALI/DSI Bus 2 .........................Load max. 30 mA or
–
ø D1&2 ...................................0 V DC and communication
ø +D2 .........................................+15 V DC +/- 20% and
DALI control ..............................Both outputs are DALI broadcast
Performance:
Time range ................................1–60 mins
Lux range ..................................50–1500 lux
Orientation lighting level ............5–100%
Orientation lighting time ............0–60 mins, infi nite.
Enclosure class .........................IP 20
Insulation class ..........................CL. I
Ambient temp. ...........................-5°C to +50°C
Approval:
CE in accordance with ..............EN 60669-2-1

Accessories

IR Remote .................................................... Model 41-922
IR User Remote ........................................... Model 77-921
Settings
Factory settings:
Application .......................... App. Man
Setpoint zone 1 ................... 300 lux
Setpoint hysteresis .............. 20%
Orientation lighting level ...... 5%
Orientation lighting time ...... 1 min.
Factor zone 2 ...................... 300 lux
Off delay (Time) ................... 10 mins
Fade factor DALI ................. 0
Setting of Lux and Time ...... Via IR Remote
Output bus .......................... DALI
Servodan A/S | Tel +45 7442 4726 | Fax + 45 7442 4035 | info@servodan.dk | www.servodan.com
20 light fi ttings.
communication
20 light fi ttings.
communication
(selectable 0-15 in acc. with DALI standard)
LED indicators:
Green LED fl ashes when the pushbutton power switch or the IR
Remote is activated.
If the buttons on the IR-remote are pressed, the sensor is
unlocked and there is no indication from the Green LED, then the
sensors is in min. or max. of the settings.
Blue LED is lit when test mode is selected.
Blue LED fl ashes when setting the setpoint, indicating over-
illumination.
Red LED fl ashes when, the detector is in test mode and activity
is detected.
Manual dimming using the pushbutton:
When the dim function has been activated, the lighting must be
switched off so that it can be switched on, and thus function with
daylight control (according to built-in light sensor).
DALI or DSI:
Switch between DALI and DSI control using DIP switch 2 (see
Fig. 5).
Function App. Man
Manual, Factory settings.
Function description:
Ceiling lighting
Two zone DALI or DSI daylight control is switched on and off via
a pushbutton.
The two zones are connected to their own DALI or DSI bus in
zones 1 + 2.
The light can be switched on when light is needed according to
the preset parameter.
As long as the presence detector registers activity, the lighting
will be adjusted according to the preset parameters.
As daylight increases, lighting in the room starts to dim until the
preset minimum light level is achieved.
If there is suffi cient incident daylight, the lighting switches off.
The light switches off automatically after a preset period, when
the presence detector does not register activity within the
detection area.
Dimming of lighting
A long press of the pushbutton enables the lighting to be
adjusted up/down.
Manual override using IR Remote.
Function App. Auto
You must use an IR Remote (accessory) to select App. Auto.
Function description:
Ceiling lighting
When a presence detector registers activity and light is required,
the lighting comes on automatically in two zones, DALI or DSI
daylight control.
The two zones are connected to their own DALI or DSI bus in
zones 1 + 2.
As long as the presence detector registers activity, the lighting
will be daylight-controlled according to the preset parameters.
As daylight increases, lighting in the room starts to dim until
the preset minimum light level is achieved. If there is suffi cient
incident daylight, the lighting switches off.
GB
7(17)