Werbung
Verfügbare Sprachen
Verfügbare Sprachen
o
The original threaded connection on the head is compatible with a connector from the trade
o
The original threaded connection on the head is compatible with a connector from the trade
because it is a usual 2" thread.
o
because it is a usual 2" thread.
The sealing between the threaded connector and the filter head is completed by a sealing
o
The sealing between the threaded connector and the filter head is completed by a sealing
ring; hand-tightening with two hands is sufficient for low pressures. For higher pressures,
ring; hand-tightening with two hands is sufficient for low pressures. For higher pressures,
around 10 bar, tightening with a strap wrench is recommended. Checking the tightness is
around 10 bar, tightening with a strap wrench is recommended. Checking the tightness is
required when pressurising.
required when pressurising.
o
The tightness between the head and the bowl is ensured by an O-ring; tightening slightly with
o
The tightness between the head and the bowl is ensured by an O-ring; tightening slightly with
the two hands is adequate. The supplied spanner only helps for dismounting.
the two hands is adequate. The supplied spanner only helps for dismounting.
o
The adaptor of the drain valve (lower part) is standard mounted with a double sealing joint.
o
The adaptor of the drain valve (lower part) is standard mounted with a double sealing joint.
This adaptor can turn on 360° without causing any damage to the bowl.
This adaptor can turn on 360° without causing any damage to the bowl.
o
The cylindrical support of the filter sleeve is equipped on both ends with a centrifugal vane
o
The cylindrical support of the filter sleeve is equipped on both ends with a centrifugal vane
and a sealing cap. A joint overmolding was developed to this end.
and a sealing cap. A joint overmolding was developed to this end.
o
Placing upstream and downstream valves on the pipe is recommended in order to make the
o
Placing upstream and downstream valves on the pipe is recommended in order to make the
maintenance easier.
maintenance easier.
4. Maintenance
4. Maintenance
Before dismounting the bowl, close the upstream and downstream valves and release the pressure.
Before dismounting the bowl, close the upstream and downstream valves and release the pressure.
Filter sleeve:
Filter sleeve:
o
Maintenance and replacement of the filter sleeve used for drinking water is recommended at
o
Maintenance and replacement of the filter sleeve used for drinking water is recommended at
least 3 times per year and in any case before the pressure loss reaches 2 bar.
o
least 3 times per year and in any case before the pressure loss reaches 2 bar.
The filters graded 1, 5, 10, 25, 50 & 100 µ are intended for a single use. Cleaning them would
o
The filters graded 1, 5, 10, 25, 50 & 100 µ are intended for a single use. Cleaning them would
change the structure of the fibre, so degrading the fineness of the selected filtering and making
change the structure of the fibre, so degrading the fineness of the selected filtering and making
the filter more fragile, which could lead to tearing.
the filter more fragile, which could lead to tearing.
o
The nylon filters graded 150 & 300 µ are designed to be cleaned and re-used.
o
The nylon filters graded 150 & 300 µ are designed to be cleaned and re-used.
The bowl:
The bowl:
o
The thread of the bowl must stay clean and greased for easy fitting and removal of the bowl
o
The thread of the bowl must stay clean and greased for easy fitting and removal of the bowl
during its life time.
during its life time.
o
The sealing O-ring between the head and the bowl must also remain clean and greased for a
o
The sealing O-ring between the head and the bowl must also remain clean and greased for a
good sealing.
good sealing.
o
All slots and O-ring surroundings must remain clean and without burrs.
o
All slots and O-ring surroundings must remain clean and without burrs.
Damaged component:
Damaged component:
o
Every component of the filter, even if only slightly damaged, must be replaced immediately to
o
Every component of the filter, even if only slightly damaged, must be replaced immediately to
ensure good performance under pressure and water-tightness of the whole filter.
ensure good performance under pressure and water-tightness of the whole filter.
5. Warranty
5. Warranty
The choice of high-quality raw materials for manufacturing each component of your filter is the best guarantee
The choice of high-quality raw materials for manufacturing each component of your filter is the best guarantee
to offer you full satisfaction for many years of use.
to offer you full satisfaction for many years of use.
If, nevertheless, a component reveals a fault related to a manufacturing defect, this would be covered by a
If, nevertheless, a component reveals a fault related to a manufacturing defect, this would be covered by a
replacement of that component under guarantee.
replacement of that component under guarantee.
For further information about CINTROPUR products, go to www.cintropur.com.
For further information about CINTROPUR products, go to www.cintropur.com.
EN
EN
EN
EN
EN
8
8
Werbung
