Controls And Functions - FlEXSYS f15 Bedienungsanleitung

FLEXSYS F212 - F315 FLEXSYS F212 - F315
DESCRIPTION
The FLEXSYS series bi-amped speakers are equipped with
®
DIGIPRO series class D amplifier. This high-efficiency
amplifier delivers high output power in a compact size at low
weight. Thanks to its high efficiency the cooling of the
amplifier module is obtained statically, thus avoiding the use
of a fan.
The power supply circuits of the DIGIPRO amplifier has
been conceived to work in full-range mode; thanks to the
SMPS (Switched-Mode Power Supply) technology with PFC
(Power Factor Correction) the operation with supply voltages
between 100 Vac and 240Vac is guaranteed by ensuring the
same sound performances even with floating and non-
stabilized power supply systems.
FLEXSYS F212 (2 ways)
The F212 bi-amped active speaker is equipped with a
®
DIGIPRO amplifier which delivers 500W RMS for the bass
section and 250W RMS for the high frequency section.
The F212 active two-way speaker features two 12" (voice coil
2.5") woofers and a neodymium 1"(voice coil 1.75")
compression driver. The phase plug attached to the front of
the upper 12" woofer avoids the vertical phase modulation
which usually take place in this type of configuration and
ensures a precise horizontal coverage of the medium
frequencies.
The speaker is made of 15mm birch ply wood, the 4 handles,
the 12 M10 threads located on the sides and the back of the
speaker are enabling easy transport and installation.
The trapezoidal-shaped housing (20° angle) allows the side-
by-side setup of several speakers in cluster configuration. For
side-by-side installation, the horn must be turned (40° x 60°)!
The bottom features a adjustable foot (in height) to inclinate
the tilt angle up to a max. of 5°. This allows to direct the sound
radiation without using additional supports.
In the bottom of the box there is a standard pole mount cup
(D36mm) made of aluminium
FLEXSYS F315 (3 ways)
The F315 active speaker is equipped with a DIGIPRO
amplifier delivering 500W RMS for the bass section featuring
a 15" woofer (voice coil 3") and 500W RMS for the mid-high
section featuring a passive filter driving a 6" midrange (voice
coil 2") and a 1" compression driver (voice coil 1.5").
The speaker is made of 15mm birch ply wood, the 4 handles,
the 12 M10 threads located on the sides and the back of the
speaker are enabling easy transport and installation
The 15" woofer and the midh-high section with horizontal 90°
coverage is the ideal solution for all demanding full-range
applications .
In the bottom of the box there is a standard pole mount cup
(D36mm) made of aluminium
19
®
®
FLEXSYS F212 - F315 FLEXSYS F212 - F315

CONTROLS AND FUNCTIONS

1) " BALANCED INPUT" INPUT CONNECTOR
Balanced input at line level. Accepts "XLR" sockets.
2) "BALANCED LINK /OUT " OUTPUT CONNECTOR
The "XLR" connector connected in parallel with input (1) can be used to send the
input audio signal to another active speaker.
3) "LIMITER" INDICATOR LIGHT
This indicator shows red to indicate that the internal limiter circuit has tripped.
This prevents amplifier distortion and protects the speakers against overloads.
4) "SIGNAL" INDICATOR LIGHT
This indicator showscomes on green to indicate the presence of the audio signal (at
a level of -20dB).
5) "MUTE" INDICATOR LIGHT
This yellow indicator indicates amplifier status.
The LED is off in normal operating conditions.
6) "READY" INDICATOR LIGHT
This indicator shows green to indicate that the main power voltage is correct.
The LED shows green in normal operating conditions
7) "INPUT SENS" INPUT SENSITIVITY CONTROL
This control adjusts the sensitivity of the signal amplifier input.
This control does not affect the "BALANCED LINK/OUT" output level
FLEXSYS F212
8) "MODE" SWITCH
This two-way switch allow to choose between two different system presets.
The "SINGLE SPEAKER" position allows linear response when one single speaker
is used.
The "CLUSTERED SPEAKER" position reduces the medium-bass frequencies
which are coupling by the side-by-side attachment of several speakers.
9) "MAINS INPUT" POWER SOCKET
For connecting the power cable provided.
The connector used for mains connection is a POWER CON® (blue) socket
10) "MAINS OUTPUT LINK" POWER SOCKET
For linking the mains power. The output is connected in parallel with input (9) and
can be used to power another active speaker.
The connector is a POWER CON® (grey) socket
11) "MAINS FUSE" FUSE CARRIER
Mains fuse housing.
FLEXSYS F315
8) "MODE" SWITCH
This two-way switch allows to choose between two different system presets.
The "FLAT" position allows linear response of the speaker, which is mainly suitable
for the "live" application in closed rooms.
The "PROCESSED" position increases the low frequencies and it is suitable for
music play back or for the use in open air applications.
9) POWER CABLE SOCKET "MAINS INPUT"
Used for connecting the power cable supplied.
10) FUSE CARRIER "MAINS FUSE"
Mains fuse housing.
11) POWER SWITCH "POWER"
Switches the active speaker on and off.
REFERENCE DRAWINGS AT PAGES 51 and 52
20