Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Operation
Always check and refill oil before the start!
The oil level should always be between min. and max
on the dipstick. Fill with SAE-30 oil follow instrucktion I
engine manual. Use only unleaded 95 octane fuel to the
engine. Never overfill the tank.
Cutting height adjustment: Illustration 3-3
(The illustrations may vary from your actual model)
The mower has 5 different heights. The cutting height
ranges from 35 mm to 75 mm
Start
Never start the mower directly on long grass.
Electrical starter, illustration 3
By cold engine set the choke lever on "Choke"-
1.
By warm engine set the choke lever on "Run"
2.
Move the gear lever to postion N
3.
Regulate the height adjustment from 1 to 5.
4.
Press the foot pedal fully.Turn the engine key
to start(on) and return the choke lever in
the"run" position. (only cold engine).
Set speed lever in gear from 1 to 4 (R)
5.
Release the hand brake
6.
Activate the blades and release the foot pedal.
Recoil with choke, speed lever
By cold engine set the choke lever on "Choke"-
1.
By warm engine set the choke lever on "Run"
2.
Move the gear lever to postion N
3.
Regulate the height adjustment from 1 to 5.
Press the foot pedal fully.Turn the engine key
to start(on). Pull the recoil starter gently until
you feel resistance in the rope, then pull
quickly and energetic. Do not at any time let go
of the recoil starter but slide it gently into
starting position and return the choke lever in
the"run" position (only cold engine).
Set speed lever in gear from 1 to 4 (R)
4.
Release the hand brake
5.
Activate the blades and release the foot pedal.
Regulation of speed
Speed can be adjusted from 1.5 – 4.6 km/h while
driving. Activate the right handle on the dashboard and
set in one of the 4 different speeds or reverse. When
driving in one the two lowest speeds the pace
difference will not vary significantly.
Stop: Illustration 3-6
1.
Turn the ignition key to the off position.
Note: The blades will still rotate at up to 3 seconds
after stopping.
Water nozzle
The left side of the mower deck is fitted with a water
nozzle for washing the deck. See Illustration 1-D
Attach a hose to the nozzle.
Turn on the water and start the engine.
Activater the blades. The rotations of the
blades will ensure that the water will clean the
underside of the deck.
Note: For best result clean the deck with the water
nozzle function right after each mowing. If the grass
dries out, this function will not work optimally.
Blade
Inspection of the blade
Inspect blade for damage, cracks or excessive
rust or corrosion.
Check that the blade bolt is tightened.
Note: A dull blade can be sharpened! But a blade that
is worn, bent, cracked or otherwise damaged must be
replaced.
Mounting the blade
If you remove the blade to sharpen or replace it, you
must use the correct tool and some heavy gloves to
protect your hands.
1.
Loosen the blade bolt. Use a piece of wood to
prevent the blade from turning around.
2.
Remove the bolt, washer, blade and blade
holder in that order
3.
Sharpen or replace the blade.
4.
Insert the blade holder, blade, washer and bolt
in that order.
5.
Tighten the blade bolt. Use a piece of wood to
prevent the blade from turning around.
Warning: A blade must be sharpened so it is in
100 % balance, otherwise it may cause vibrations that
could damage the engine. Damage to engine due to
faulty sharpening is not covered by warranty. We
therefore recommend letting a service center sharpen
the blade.
Spark plug
1.
Remove the spark plug.
2.
Brush off dirt from the spark plug.
3.
Use a spark plug wrench to loosen the spark
plug.
4.
Check the insulation is intact.
5.
Clean the spark plug with a wire brush.
6.
Measure the electrode, taking care not to
damage the electrode.
7.
The distance should be: 0.7 to 0.8 mm
8.
If the spark plug is undamaged refit or replace.
9.
Reattach the spark plug.
7
Werbung
Inhaltsverzeichnis
