Werbung
The product is a new saving-energy switch; it adopts microwave sensor
EN
mould with high-frequency electro-magnetic wave (5.8GHz), integrated
circuit. It gathers automatism, convenience, safety, saving-energy and
practicality functions. The wide detection field is consisting of detectors. It works by receiving
human motion. When one enters the detection field, it can start the load at once and identify
automatically day and night. Its installation is very convenient and its using is very wide.
Detection is possible through doors, panes of glass or thin walls.
SPECIFICATION:
Power Sourcing: 220-240V/AC
Power Frequency: 50Hz
Ambient Light: <3-2000LUX (adjustable)
Time Delay: Min.10sec±3sec
Max. 12min±1min
Rated Load: 1200W
300W
FUNCTION:
Can identify day and night: It can work in the daytime and at night when it is adjusted on the "sun" position (max). It can
work in the ambient light less than 3LUX when it is adjusted on the "3" position (min). As for the adjustment pattern,
please refer to the testing pattern.
SENS adjustable: It can be adjusted according to using location. The detection distance of low sensitivity could be only
5m and high sensitivity could be 15m which fits for large room.
Time-Delay is added continually: When it receives the second induction signals within the first induction, it will restart
to time from the moment.
Time–Delay is adjustable. It can be set according to the consumer's desire. The minimum time is 10sec±3sec. The
maximum is 12min±1min.
NOTE: the high-frequency output of the HF sensor is <0.2Mw- that is just
th
one 5000
of the transmission power of a mobile phone or the output of a
microwave oven, the baby can't touch it
INSTALLATION: (see the diagram)
Unload the faceplate of sensor and adjust the time and LUX knob.(refer to figure 1)
Loose the screws in the connection terminal, and then connect the power to connection terminal of sensor according
to connection-wire diagram.
If you want to install it in circular hole, put the sensor into the hole and tighten the splay bolt on both sides (refer to
Detection Range: 180°
Detection Distance: 5-15m (adjustable)
HF System: 5.8GHz CW radar, ISM band
Transmission Power: <0.2mW
Installing Height: 1-1.8m
Power Consumption: approx 0.9W
Detection Motion Speed: 0.6-1.5m/s
figure 2). If you want to install in quadrate hole, put the sensor into the hole, fix the screw through the mounting hole
(refer to figure 3).
Install back the faceplate, switch on the power and then test it.
Figure1
CONNECTION-WIRE DIAGRAM:
TEST:
Turn the LUX knob clockwise on the maximum (sun). Turn the
SENS knob clockwise on the maximum (+).Turn the TIME knob
anti-clockwise on the minimum (10s).
When you switch on the power, the light will be on at once. And
10sec±3sec later the light will be off automatically. Then if the
sensor receives induction signal again, it can work normally.
When the sensor receives the second induction signals within the
first induction, it will restart to time from the moment.
Turn LUX knob anti-clockwise on the minimum (3). If the ambient
light is less than 3LUX (darkness), the inductor load could work
when it receives induction signal.
Note: when testing in daylight, please turn LUX knob to
lamp could not work!
：
NOTES
Electrician or experienced human can install it.
Can not be installed on the uneven and shaky surface
In front of the sensor there shouldn't be obstructive object affecting detection.
Avoid installing it near the metal and glass which may affect the sensor.
For your safety, please don't open the case if you find hitch after installation.
Figure2
Figure3
(SUN) position, otherwise the sensor
Werbung
