Global Settings; Midi - Hughes & Kettner Black Spirit 200 Handbuch

Black Spirit 200 – Manual 1.1b
5 Bluetooth Audio Streaming: You can stream audio to your Black Spirit
200 to play along to your favorite songs. The audio signal is fed in full
stereo quality to the headphones out (that also serves as a stereo line out,
see 5.21), and in mono to the speaker out when the speaker out is set to
fullrange (see 6.1). This lets you connect your home hi-fi system to the
headphones out or a non-powered PA cabinet to enjoy your playing and
your jam tracks without any additional mixers.

8 MIDI

As you've learned in chapter 2.2, presets can only be changed via MIDI.
Sender (controller) and receiver (amp) must use the same channel. The
factory default is MIDI channel 1 and "Omni On". If the amp does not react
to program changes properly, the MIDI channel has to be changed.
8.1 Setting MIDI channels and switching
Omni On/Off
Press and hold FX Access and FX Loop simultaneously for three seconds.
The Store button will light up. This assigns special programming functions
to the following LEDs and buttons:
• Boost: lights up to indicate Black Spirit 200 is configured to receive
incoming program changes via all MIDI channels (Omni On, default). If
the LED is not illuminated, the amp receives messages via the selected
channel only (Omni Off). To change the Omni mode, just press the Boost
button.
• FX Loop now serves as a +1/up button, while FX Access now serves as a
-1/down button. Use these buttons to change the MIDI channel.
• When configuring MIDI channels, the four Channel LEDs serve to
indicate the MIDI channels. Consult the table below for the MIDI channel
assignments. They show what in tech-speak is called binary code:
MIDI Channel Clean
1 = ¢
2 =
¢
3 =
¢
4 =
¢
5 =
¢
6 = ¢
7 =
¢
8 =
¢
9 =
£
10 =
£
11 = £
12 =
£
13 =
£
14 =
£
15 =
£
16 = £
Press and hold the Store button for three seconds to save the settings and
quit MIDI setup mode. The amp is now back in normal
operating mode.
10
Crunch Lead Ultra
¢ ¢ ¢
¢ ¢ {
¢ £ ¢
¢ £ £
£ ¢ ¢
£ ¢ £
£ £ ¢
£ £ £
¢ ¢ ¢
¢ ¢ £
¢ £ ¢
¢ £ £
£ ¢ ¢
£ ¢ £
£ £ ¢
£ £ £

8.2 Global Settings

If you press the Store and FX Loop buttons simultaneously for three
seconds, the Store button will start flashing. The following LEDs and
buttons on the amp will then serve special programming purposes:
• FX Access: This indicates the status of Global EQ mode. The button
lights up when Global EQ mode is active. To deactivate it, press the FX
Access button again.
• FX Loop: This indicates the status of Global Cabinet type Mode. The
button lights up when Global cabinet type mode is active. To deactivate
it, press FX Loop again.
Press and hold the Store button for three seconds to save the settings and
quit Global settings mode. The amp is now back in normal operating
mode.
8.3 MIDI implementation chart / controller list
In addition to controlling all switching functions via MIDI program changes,
you can also change the parameters of every single editable function of the
amp in real time via MIDI control changes. The following chart shows the
editable functions and the corresponding controller numbers:
Controller Function
number
1 Modulation Intensity
4 Delay Time, 128 steps, 51 ms to 1360 ms
7 Volume (soft)
9 Mute On-Off. On status remains active until the amp channel is changed,
the volume parameter is changed or the amp is re-started.
12 Mod-FX Type
20 Gain (soft)
21 Bass
22 Mid
23 Treble
24 Resonance
25 Presence
26 Modulation Speed (always for the active modulation effect)
27 Delay Feedback
28 Delay Volume
29 Reverb Volume
31 Channel Switching (4 sectors)
52 Mod-FX On-Off
53 Delay On-Off
54 Reverb On-Off
55 FX Loop On-Off
56 Gain (hard)
57 Volume (hard)
58 Cabinet Type (8 sectors)
59 Sagging (8 sectors)
62 Noise Gate Sensitivity
63 Noise Gate On-Off
64 Boost On-Off
Heads up: You can adjust Black Spirit 200's volume levels via a controller
pedal (MIDI controller #7), but only up the maximum value stored in the
amp. This means that a controller pedal connected to the FSM-432 does
not work like a global remote control for the amp's overall volume level