Maintenance - Ferm FBJ-710 Gebrauchsanweisung

GB
• Move the motor base backward and switch the machine off.
Move the machine in the same direction as the direction of rotation. See arrow on
top of the machine (16).
NL
Joining the workpieces
When the grooves in both workpieces have been made the workpieces can be joined together.
F
• Put glue in both grooves.
• Place the biscuit dowel in the groove of one workpiece.
• Place the other workpiece on the biscuit dowel.
E
• Fasten the workpieces and wait till the glue is dry.
User tip for connecting two workpieces
P
Fig. K
• Saw a groove as big as one biscuit into the first workpiece
• Place the biscuit with good glue (according the material) into the groove
I
• Saw a longer groove into the other workpiece
• Now both workpieces can be positioned easily towards each other (clearance to correct)
• Fasten the workpieces and wait till the glue is dry
S
Checking the cutting depth
SF Fig. J
Always check the cutting depth after mounting a saw blade.
N
• Disconnect the plug from the socket.
• Move the motor base (15) as far as possible backwards.
• Set the cutting depth in the maximum position by turning the depth adjustment knob (7).
DK
• Move the motor base forwards till the pin (A) will fall in the notch of the adjustment knob (7).
Turn the saw blade till one tooth of the saw blade is in the front position.
• Measure the distance from the side of the base plate to the tooth of the saw blade
• Check if the distance is 18 mm. the maximum position is 18 mm.
Setting the cutting depth
When the cutting depth is not correct, it can be adjusted as following.
• Move the motor base (15) as far as possible backwards.
• Loosen the pin (A).
• Set the cutting depth by turning the screw, the screw is positioned at the back of the pin (A).
• Repeat the procedure till the cutting depth is correct
• Fasten the pin (A).

6. MAINTENANCE

Make sure that the machine is not live when carrying out maintenance work on the
motor.
12
Kontroller maskinen, løsdele og tilbehør for transportskade.
Komponenter
Fig. A
FBJ-710 skyggefugefræser er velegnet til at fræse skyggefuger til dyvelsamlinger i massivt
træ, krydsfiner, spånplader, fiberplader, plexiglas og kunstigt marmor.
1. Tænd-sluk-knap
2. Hjælpehåndtag
3. Spindellås
4. Vinkelstop
6. Skala til vinkelanslag
7. Knap til justering af fræsedybde
8. Spændearm til vinkeljustering
9. Spændearm til højdejustering
10. Knap til højdejustering
11 Skala til højdejustering
12. Bundplade
13. Tilslutning til støvpose
14. Støvpose
15. Motorhus
16. Pil (rotationsretning)
2. SIKKERHEDSFORSKRIFTER
I denne brugsanvisning anvendes de følgende piktogrammer:
Læs instruktionerne omhyggeligt
I overensstemmelse med grundlæggende sikkerhedsstandarder i de europæiske
direktiver.
Klasse II maskine – Dobbelt isolering – Du behøver ingen jordforbindelsestik.
Betegnelse for risiko for personskader, dødsfald eller beskadigelse af værktøjet i
tilfælde af at du er uopmærksom på instruktioner i denne manual.
Indikerer farer for elektrisk stød
Tag straks stikket ud af stikkontakten, hvis ledningen beskadiges og i forbindelse
med vedligeholdelse
Ferm Ferm
UK
D
NL
F
E
P
I
S
SF
N
DK
97