Troubleshooting; Technical Data; Ce Declaration Of Conformity - Chicco CuociPappa Natural Anleitung

X. TROUBLESHOOTING
PROBLEM
The display does not come on
The symbol appears on the
display and there is a beep every 10
seconds
The symbol appears on the
display.
The appliance will not blend or the
cooking cycle will not start
A bad smell or excessive noise comes
from the motor unit during blending
Food leaks from the jug during
blending
The appliances takes too long to
produce steam or does not produce any
The food is not cooked properly
Steam coming out of the boiler cap
area
The "add water" signal is activated
at the start of or during the cooking
cycle
The cap will not come off the jar
after cooking
After cooking, there is water
under the water tank or under the
appliance
Water leaking from the tank
XI. TECHNICAL DATA
Model: MEC-6131V
Supply voltage: 220-240 V~, 50/60 Hz
Boiler power: 400 W
Motor power: 140 W
Blender operating cycles: 10 sec. ON – 10 sec. OFF
Made in China
KEY TO SYMBOLS
= Appliance complies with the essential require-
ments of the applicable EC Directives
= CAUTION!
= CAUTION! Hot steam
= Read the operating instructions
= Caution! Hot surface
= Operating instructions
POSSIBLE CAUSES
· Power cord not properly inserted in
the appliance
· The water tank is missing or has not
been filled or positioned correctly
· The water does not flow freely from
the tank to the boiler
· Lime scale accumulation in the boiler
· The boiler has overheated due to the
accumulation of lime scale
· The boiler has overheated due to
repeated cooking cycles
· The jug or the lid are not in the right
position
· New product
· Too much food
· Food that is too hard in the jug
· Blending times too long
· Too much food in the jug or the food
is too liquid
· Limescale accumulation in the boiler · Perform cleaning and maintenance on the boiler
· Pieces of food too large
· Too much food in the basket
· Cooking times not adequate
· The boiler cap is not inserted or is
not properly closed
· The steam outlet is obstructed by
food residue or limescale
· The water tank is missing or has not
been filled or positioned correctly
· The water does not flow freely from
the tank to the boiler
· Overheating
· Blade unit missing or positioned
incorrectly
· Blade seal missing or positioned
incorrectly
· Cap not closed properly
· Seals missing or positioned incorrectly
15
POSSIBLE SOLUTIONS
· Check that the power cord is inserted correctly into
the connector and that the appliance is plugged in
· Switch off the appliance and unplug it. Fill the tank
with water before restarting the cycle.
· Switch off the appliance and unplug it. Leave it to cool
completely (at least 30 minutes) then clean.
· As above
· Switch off the appliance and unplug it. Leave it to cool
completely (at least 30 minutes) then clean.
· Leave the appliance to cool between one cycle and
the next
· Position the jug and lid correctly so that the safety
switches are activated
· During the first uses, this is normal
· Reduce the amount of food in the jug
· Do not blend food that is too hard. Defrost food
before blending it.
· Follow the recommended blending times, leaving the
appliance to cool to prevent overheating.
· Reduce the amount of food or liquid in the jug
· Cut food into smaller pieces
· Reduce the amount of food
· Set longer cooking times
· Position the boiler cap and close it well
· Perform cleaning and maintenance on the boiler If
necessary, clear the steam outlet without damaging
the seal
· Position the tank correctly after filling it with a
suitable volume of water
· Perform cleaning and maintenance on the boiler
· Wait a few minutes and allow to cool
· Insert the blade unit in the jug and turn it until it is
securely fitted
· Check the presence and position of the seal
· Tighten the cap
· Check the presence and position of both seals
= IMQ marking
Do not dispose of this product or its components
as household waste, but recycle, referring to
specific legislation in force in the country of use.
Warranty
This appliance is guaranteed against manufacturing defects
for two years from the date of purchase (the date shown
on the receipt or other proof of date of purchase) or for any
other period envisaged by the applicable law in the country
of purchase. The warranty does not cover parts subject to
normal wear.

CE DECLARATION OF CONFORMITY

Artsana S.p.A. hereby declares that this appliance, the Chicco
brand MEC-6131V model, meets the essential requirements
and other relevant provisions of Directives 2004/108/EC
(Electromagnetic Compatibility) and 2006/95/EC (Electrical
Safety). A full copy of the CE declaration may be requested
from Artsana S.p.A. Via S. Catelli 1, 22070 Grandate (CO), Italy.