Braun JB 7192 Bedienungsanleitung Seite 11

(A) Jug
Assembly
• Ensure that the blade gasket (5a) is positioned
on the inside rim of the blade group (5b).
• Carefully place the blade group into the locking
ring (5c).
• Screw the blade assembly (5) to the jug (4) in a
clockwise motion until it can go no further.
Blending with the Jug
• Make sure the appliance is turned off .
• Position the line on the locking ring (5c) in front
of you and push the jug down until it is securely
locked into place. The jug handle should be on
the right or left side of the motor body. When
properly positioned, the jug will rest completely
on the motor body.
• Add liquid ingredients fi rst, followed by solid
ingredients. This will ensure all ingredients are
uniformly blended and prevent unnecessary
stress on the motor. Firmly place the complete lid
(1,2,3) on top.
• Plug in the power cord.
• Turn the appliance on by pressing the On/Off
button (7).
• The indicator lights (8,9,10) will fl ash. To start
operation select a pre-programmed speed (refer
to «Operating Instructions»).
• Always stop the blender when adding more
ingredients. Ensure the complete lid including
the measuring cap is replaced.
• During operation, you may add liquids through
the drip hole in the measuring cap.
• When fi nished, press the pre-programmed speed
button.
• To switch off the appliance, press the On/Off
button and unplug blender before removing the
jug.
Recipe example: Vanilla-Honey-Prunes
(as a pancake stuffi ng or spread):
Fill the jug with 300 g pitted prunes and 200 g honey
Pulse at speed 5 for 5 seconds
Add 500 ml water (vanilla-fl avoured)
Blend for 8 seconds in total
(B) Smoothie2Go Attachment
NOTE: The Smoothie2Go must only be operated
using its special blade group (13b) and for pre-
paring drinks and smoothies.
Assembly
• Ensure that the blade gasket is positioned on the
inside rim of the blade group (13b).
• Hold the blade group at the coupling from
underneath and place it upside down in the cup.
• Screw the locking ring (5c) to the cup (12c) in a
clockwise motion until it can go no further.
Blending with the Smoothie2Go
Attachment
• Make sure the appliance is turned off .
• Fill the cup (12c) with ingredients. Ingredients
should be added in reverse order of the regular
jug – solids fi rst, then liquids.
• Carefully place the blade group including gasket
onto the cup.
• Screw the locking ring in a clockwise motion until
it can go no further.
• Turn the cup upside down, position the line on
the locking ring (5c) in front of you and push the
cup down until it is securely locked into place.
• Plug in the power cord.
• Turn the appliance on by pressing the On/Off
button (7).
• The indicator lights (8,9,10) will fl ash. To start
operation select a pre-programmed speed (refer
to «Operating Instructions»).
• When fi nished, press the pre-programmed speed
button.
• To switch off the appliance, press the On/Off
button and unplug blender before removing the
Smoothie2Go attachment.
• When fi nished blending, pull the cup straight up
to remove from the base.
• Turn the cup upright and remove the blade
assembly by twisting it counterclockwise.
• To remove the blade group from the locking ring,
push with both thumbs from inside the ring until
it snaps out.
• To attach the lid to the cup, ensure the gasket
(12b) is inside the rim of the lid (12a) and twist
clockwise. Carefully close the drinking spout.
NOTE: The Smoothie2Go attachment must not be
used to blend hot foods, carbonated liquids or food
supplements.
When preparing protein shakes using powder and
liquids only, use the jug.
Operating Instructions
NOTE: The blender will only operate when the On/
Off button is pressed before selecting the desired
speed or mode.
After 2 minutes of processing time the appliance
stops blending automatically. The indicator lights
(8,9,10) will fl ash. To re-start operation press a
speed button again.
Speed Selection
• Start blending by pressing one of the speed
buttons (9).
• The indicator light of the selected function will
glow and all other lights will turn off .
11