Inhaltszusammenfassung für thomann Harley Benton PowerPlant
Seite 2
Herzlichen Glückwunsch zum Erwerb dieses Multinetzteils. Wir empfehlen Ihnen, diese Anleitung zu studieren, bevor Sie das Gerät in Betrieb nehmen. Bestimmungsgemäßer Gebrauch • Dieses Multinetzgerät ist ausschließlich zur Spannungsversor- gung von Geräten bestimmt, sie selbst über kein Netzteil verfü- gen. Das Gerät ist nicht zur Verwendung in gewerblichen oder industriellen Bereichen vorgesehen.
Wichtige Sicherheitshinweise Zu Ihrer eigenen Sicherheit sollten Sie dieses Kapitel zuerst ganz durchlesen! Gefahr durch elektrischen Schlag! • Schließen Sie das Gerät nur an eine ordnungsgemäß ange- schlossene und geerdete Netzsteckdose mit einer Netzspannung von 230 V ~ /50 Hz an. Trennen Sie niemals die Erdleitung des Netzkabels durch.
Seite 5
am Kabel selbst, und fassen Sie das Netzkabel niemals mit nas- sen Händen an, da dies einen Kurzschluss oder elektrischen Schlag verursachen kann. Stellen Sie weder das Gerät, oder Bo- xen o.ä. auf das Netzkabel und achten Sie darauf, dass es nicht eingeklemmt wird.
Geräteübersicht q 9V /500mA-Ausgänge w POWER - Einschaltkontrollanzeige e 12V /250mA-Ausgang /250mA-Ausgang r 12V t POWER ON/OFF - Ein-/Ausschalter y MAINS VOLTAGE - Netzanschlussbuchse u Sicherungshalter Stromanschluss 1. Schließen Sie das beiliegende Netzkabel an die Netzanschluss- buchse (y) des Gerätes an. 2.
Geräte anschließen 1. Geräte, die eine Spannungsversorgung von 9V Gleichspannung benötigen, können Sie mit den beiliegenden Kabeln an die 9V- Ausgänge 1 - 8 (q) anschließen. Achtung! Für alle angeschlossenen Geräte zusammen steht ein maximaler Strom von 500mA zur Verfügung. Überlasten Sie das Gerät niemals! 2.
3. Entnehmen Sie die defekte Sicherung und ersetzen Sie sie durch ein neue gleichen Typs (250V T100mA). 4. Schieben Sie den Sicherungshalter wieder in die Netzan- schlussbuchse, bis er einrastet. Reinigung Reinigen Sie das Gerät mit einem trockenen weichen Tuch. Mit einem leicht befeuchteten Tuch können hartnäckiger Dreck und Schmutz vom Gerät entfernt werden.
Contents Safety information ..............10 The control elements ..............12 Power connection ..............12 To switch on/off ................. 12 Connect devices................. 13 To change the fuse ..............13 Cleaning ..................14 Technical specifications .............. 14 Disposal ..................14 Congratulations on your purchase of this power supply. We recommend to read this manual carefully before using the product for the first time.
Safety information For your own safety you should first read this chapter completely. Risk of electrical shocks! • Connect the device exclusively to a properly wired and earthed electrical wall socket with a mains voltage of 230 V~ / 50 Hz. Never cut the earth wire of the mains cable.
Seite 11
• Always grasp the power cord by the plug. Do not pull on the cord itself and never touch the power cord with wet hands as this could result in a short circuit or an electrical shock. Do not place the device, speaker boxes or anything else on the power cord and make sure that it does not become clamped.
The control elements q 9V /500mA output w POWER - operating indicator e 12V /250mA output /250mA output r 12V t POWER ON/OFF - on/off switch y MAINS VOLTAGE - power cord socket u Fuse holder Power connection 1. Connect the power cord provided to the MAINS VOLTAGE socket of the unit.
Connect devices 1. Use the cables enclosed to connect devices, that require 9V DC voltage, to the 9V outputs 1 - 8 (q). Attention! The unit provides a total of 500mA. All devices connected to the 9V outputs share the current. Never overload the unit! 2.
Cleaning Clean the housing surface with a dry or slightly damp cloth. Never use cleaners such as thinner or alcohol. Technical specifications 1 Power Supply ...... : 230V~/50Hz 2 Outputs ......: 8 x 9V /500mA max..........: 1 x 12V /250mA max..........