Werbung
Verfügbare Sprachen
Verfügbare Sprachen
18815 Laptop holder
- for K&M-Keyboard-Tables 18810, 18950 and 18953
- variable adjustment of height, direction, distance and angle
- laptop connections are always accessible thanks to the flexible edge pins
- Desk area: Height 238 mm x Width 356 mm
Thank you for choosing this product. This instruction manual informs you about the important
steps to set up and handle the product. We recommend to keep the manual in a separate place
for a possible later use.
SAFETY NOTES
- Only for laptops and manuscripts
- Always ensure that the screw connections are tight and in working order.
- Clamp prism c may only be installed with the slits facing downward.
- Edge pins k are to be placed in such a manner that the Laptop is secure.
- Only for K&M-Keyboard-Tables 18810, 18950 und 18953
SETUP INSTRUCTIONS
1.APPLICATION AREA
1.a Table-style keyboard stand »OMEGA« 18810 - without adjustment adapter d
1.b Table-style keyboard stand 18950 - with adjustment adapter d
1.c Table-style stage piano stand 18953 - with adjustment adapter d
2. COMPONENTS
Please perform a visual inspection to ensure that all parts and components are
accounted for and in working order, in particular the screw connections.
a Extension with desk plate foldable + a.1 clamp for height
b Extension and adjustable tube foldable + b.1 clamp for distance
Accessory bag A (clamp elements)
b
c Clamp prism with slit
d 2x adjustment adapter for 18950
e Clamp screw M6 x 17 mm
f Threaded pin M6 x 8 mm, SW3
g 2x Clamp nut M6, 33 mm wide
h 2x carriage bolt M6 x 20 mm
i Allen wrench / Hexagon key SW3
Accessory bag B (edge pins)
i
j 2x Cap
k 2x Edge bolt M5
l 2x Washer ø 5,3 mm
m 2x Clamp nut M5, 21 mm wide
3. MOUNT TO THE KEYBOARD STAND
Attachment to K&M-Stand18810 »Omega«
The laptop bracket can be attached to the stand tube laterally from
both sides
1 The adjustment adapter d is not needed: please remove.
2 Place locking screws M6 x 20 mm h through the rectangular holes
2
of the desk tube b and screw on the clamp nuts g.
2
Hold the desk tube bracket b up to the »OMEGA« stand tube and
2
place the clamp bracket c over the screws from above.
3 Now tighten the clamp nuts g.
4 The clamp space between the tightened brackets must be of
4
equal size.
Mounting to K&M-Tables 18950 und 18953
We recommend two people perform the installation.
All four table corners are suitable for the installation.
PREPARATION:
5 Both adjustment adapters d are needed:
5
please have them at the ready.
6 Clip both adapters in the respective brackets
6
as illustrated:
6
IMPORTANT: both adapters must be positioned
6
appropriately due to the screw heads.
6
See 6.a, b, c, d (view from above)
7 Bracket unmounted c:
7
The slits must ALWAYS face downward
INSTALLATION:
18 The prepared brackets are placed on the selec-
18
ted leg of the folding-table (6 be sure to observe
18
the recess on the adjustment adapter d.
19 First place both locking screws h through the
19
rectangular holder of the bracket on the exten-
18
sion tube b - then place it through the slits
18
on the bracket.
10 Now place and tighten the clamp nuts g.
11 The clamp space between the tightened
11
bracket must be of equal size on both sides.
1
5
6
8
1. APPLICATION AREA
1.a - K&M 18810
Keyboard stand
»Omega«
2. COMPONENTS
2
3
6.a
6.b
7
9
1. b - K&M 18950
Keyboard stand
1. c - K&M 18953
Stage piano stand
A
B
4
6.c
6.d
11
10
Werbung
