NAIM OVATOR S-800 Handbuch Seite 7

OVAT OR S-800 , S- 600 & S -40 0 – Eng lish
5 C onnect ing
Ovators incorporate a passive crossover but can be converted for use in active systems
using the appropriate Naim active crossover and multiple amplifiers. Contact your local
retailer or distributor for more information.
5 .1 Cab le s and C o nne c to rs
If your Ovators are to be used with Naim amplification,
Naim loudspeaker cable will produce the best results and
is necessary with some amplifiers. Cable lengths to both
speakers should be equal and be between 3.5 metres
and 20 metres. If the position of a speaker in relation to
the amplifier results in spare cable do not coil the cable
but lay it out back and forth between the amplifier and
speaker.
The Ovator connection terminals are intended to accept
the custom-designed Ovator speaker connector. This
connector is designed to provide the best possible
performance. Other 4mm plugs can be used, however
the results will be unpredictable. Your retailer will be able
to make up speaker cables terminated on one end by the
Ovator connector and on the other end by a connector
appropriate to the driving amplifier.
It is important that loudspeaker cables are arranged and
dressed so that mechanical stress is minimised and that no
undue force is applied to the connectors either during or
after connection.
6 Specifi ca ti ons
Frequency response:
Sensitivity:
Nominal impedance:
Suggested power amplifier:
Weight:
Dimensions H x W x D:
Note:
The colour and grain characteristics of wood finishes may vary.
7 Confo rmance To App ropr iate Standa rd s
Naim Audio declares that Naim Audio products are in conformance with:
Low Voltage Directive 2006/95/EC
Electromagnetic Compatibility Directive 2004/108/EC
Restriction of Hazardous Substances (RoHS2) Directive 2011/65/EU
Waste of Electrical and Electronic Equipment Directive 2002/96/EC
Energy Using Product Directive 2005/32/EC
Naim Audio products comply with the following standards:
EN60065 - Audio, video and similar electronic apparatus - Safety requirements
EN55013 - Sound and television broadcast receivers and associated equipment - Radio disturbance characteristics
EN55020 - Sound and television broadcast receivers and associated equipment - Immunity characteristics
EN61000-3-2 - Mains harmonics current emissions
EN61000-3-3 - Mains flicker emissions
S-800
20Hz - 35kHz (in room)
89dB @ 1m for 2.83V input
4 Ohms (min 3.9 Ohms)
25 - 250W (8 Ohm rating)
93.5kg
1393mm x 520mm x 542mm
(inc floor-spikes and grilles)
E6
5. 2 Co nnectio n Pol ar ity
It is important that Ovators are connected with the correct
polarity. Ensure that the positive terminal on each speaker
(marked +) is connected to a positive output terminal on
the amplifier and the negative terminal on each speaker
(marked – ) is connected to a negative output terminal on
the amplifier. Diagram 5.3 illustrates the Ovator connection
panel.
Note: Naim speaker cable has a rib running down one
side to aid polarity identification. The positive side of Naim
speaker plugs have a small protrusion for identification.
5. 3 Ova to r C onnec ti on P anel
S-600
28Hz - 35kHz (in room)
88dB @ 1m for 2.83V input
4 Ohms (min 3.2 Ohms)
25 - 150W (8 Ohm rating)
61kg
1168mm x 401mm x 434mm
(inc floor-spikes and grilles)
S-400
36Hz - 35kHz (in room)
88dB @ 1m for 2.83V input
4 Ohms (min 3.8 Ohms)
25 - 130W (8 Ohm rating)
31kg
1060mm x 330mm x 345mm
(inc floor-spikes and grilles)