Skymaster 2in1 Bedienungsanleitung Seite 8

D. Setup via the learning function (2433)
The learning (programming) function is used to extend the pre-programmed codes. The standard
code list already provides you with the most important functions, but it is possible to add a few
additional functions, if desired. A fully functional original remote control (from which the codes
are transferred) is required to carry out programming.
Always use new or fully charged batteries during programming.
1. Press and hold the Learn button and simultaneously press the device button which you wish to
program (e.g. DVD player). Subsequently release both buttons. The DVD device button on
your new remote control should flash; the remote control is now in DVD code programming
mode.
2. Press and release the target/function button which you wish to program (e.g. POWER). The
device button lights up.
3. Point the original remote control at the receiver LED (the same as the transmitter LED) on
your new remote control. Ensure that both remote controls are approx. 30 mm apart and
facing each other.
4. Press and hold the source button (e.g. POWER) on your original remote control until the LED
on your new remote control flashes twice, lights up for two seconds and then flashes again.
(This means that you have now programmed the POWER signal from your original remote
control and that your new remote control has returned to the programming mode for further
programming tasks.). If an error occurs, the LED flashes four times, lights up for two seconds
and then flashes again. (This means that programming of the POWER signal from your original
remote control has been unsuccessful and that your new remote control has returned to the
programming mode for further programming tasks.)
5. Repeat steps two to four to program further buttons, if desired.
Note:
1. If you wish to exit the programming mode, press and release the device button.
2. If a button is not pressed within 30 seconds, the programming mode is automatically
terminated.
3. You can simultaneously press the SET and 4 button to delete all the buttons programmed
under the device button; the LED flashes twice to confirm this command.
4. If the memory is full, the LED flashes four times and the programming mode is automatically
terminated.
5. The last programmed signal overwrites the previous one.
6. Approximately 100 commands can be stored in this remote control and approx. 40 commands
programmed for each device.
Further Functions
E. Display Device Code (2431, 2432, 2433):
You can call up the device code which you have set in your new remote control as follows:
1. Press and hold down the SET button, simultaneously press number button 1 to display the
hundreds of the 3-figure code. Count how often the LED flashes. If the LED does not flash, the
number is ZERO.
2. Press and hold down the SET button, simultaneously press number button 2 to display the
tens of the 3-figure code.
3. Press and hold down the SET button, simultaneously press number button 3 to display the
ones of the 3-figure code.
Example for code 108:
1. Press SET and 1
2. Press SET and 2
3. Press SET and 3
F. Reset / Delete Function (2431, 2432, 2433):
To delete the codes which you have set in the remote control, press and hold down the SET
button, simultaneously press the number button 0 for more than 3 seconds and then release both
buttons. The LED flashes twice and all the set-up data and commands in the remote control are
deleted.
G. Lock / Unlock volume (2431, 2432, 2433):
This function is very practical if you wish to use just one device to control the volume. For
example, you can use your amplifier as the main volume controller. In this case, you can use the
function to set the volume and mute button to AMP, regardless of which device you are using
(even if you are using a TV, DVD, VCR, etc.). The volume and mute button on your remote control
still control the volume and mute of your amplifier.
1. Press the remote control device button for which you wish to lock the volume, e.g. AMP.
2. Press the SET button and the number button 5, the current VOL and mute are locked. The LED
flashes twice as confirmation.
Note: Press the SET button and the number button 6 to unlock the volume.
8
LED flashes once.
LED does not flash.
LED flashes eight times.