Skymaster 2in1 Bedienungsanleitung Seite 7

A. Setup via brand name code (2431, 2432, 2433):
1. Switch on the device for which you wish to use the remote control (e.g. TV set).
2. Find the code number of your device brand in the code list (e.g. Lifetec 003, 010, 023, ...)
from the respective device group (e.g. TV).
3. Simultaneously press the SET button and the device button (e.g. TV). The TV device button on
your remote control lights up, i.e. it is in set-up mode.
4. You now have to enter the 3-figure device code (e.g. 003 for Lifetec TV set). If an entry does
not occur within 10 seconds, the set-up mode is automatically terminated.
5. The LED goes out if the remote control accepts the code.
If the LED flashes twice = the code is incorrect; the remote control remains in set-up mode.
If this occurs, re-enter the correct code from the list.
6. Check the function of the buttons on your remote control. If the majority of the buttons on your
new remote control do not function correctly, enter another 3-figure device code (e.g. 010...)
from the list under the same brand name. Repeat steps 3 to 6 until all the basic functions
operate correctly. The device is set up correctly as soon as you enter the correct code.
Note: Exit the set-up mode by pressing the device button (e.g. TV), or the set-up mode is
automatically terminated if a button is not pressed during a 10 second period.
B. Setup via auto search (2430, 2431, 2432, 2433):
If the set up via brand name and code was not successful or you were unable to find your brand
name in the list, you can use the Auto Search function to find the correct code for your remote
control.
1. Switch on the device for which you wish to use the remote control. If the device is a VCR,
please insert a cassette.
2. Point the remote control at the device. Simultaneously press and hold down the SET and the
device button (e.g. TV) for 3 seconds. The device button should start to flash, i.e. the device
is in Auto Search mode.
3. The OFF signal is automatically transmitted from the remote control to the device (code scan).
As soon as the device (e.g. TV) switches off, immediately press any button (except the SET
button) to terminate Auto Search.
4. Switch on the device via the POWER button. Check whether the other buttons on your remote
control function correctly. If none of the buttons function (i.e. the search cannot be stopped at
the correct time) or the majority of the buttons do not function correctly, restart the search
(see steps 2 to 4) to find a suitable code. If the majority of the buttons function correctly, set
up has been successful. Re-press the device button (e.g. TV) to save the code and to
terminate the set-up mode.
Note: To automatically terminate the search, press any button (except the SET button). The LED
goes out and the search is terminated.
C. Setup via manual search (2430, 2431, 2432, 2433):
1. Switch on the device for which you wish to use the remote control. If the device is a VCR,
please insert a cassette.
2. Point the remote control at the device. Press and hold down the SET button and then press
(for less than 3 seconds, otherwise Auto Search is started) the device button (e.g. TV). Then
release both buttons.
3. The device button lights up and the remote control is in set-up mode.
4. Press the POWER button (ON/OFF button) approx. every 1.5 seconds. (If the device you are
searching for is a VCR, DVD player, CD player, Tuner, cassette recorder, etc., you can also press
the PLAY button.). The device should start to flash, i.e. the device is in "Manual Search" mode.
5. As soon as the device you are searching for switches off (or is reactive), check whether the
other buttons on the remote control function correctly (do not press the POWER button,
otherwise it moves to the next code). If the majority of the buttons does not function correctly,
press the POWER button approx. every 1.5 seconds to initiate the reactive code (manual
search is continued, see steps 4 to 5).
If the majority of the buttons on the remote control functions correctly, save the code by
pressing the device button (e.g. TV) to terminate the manual search.
Note: The Manual Search is automatically terminated if no entry occurs during a 30 second period.
7