IMG STAGELINE LED-500DX/RGB Bedienungsanleitung Seite 15

6.1.3 Colour radiator
With this function the unit radiates at maximum bright-
ness in one of 9 colours to be selected. This function is
only available in the operating mode 2 (
1) Press the button MENU (9) so many times until
is displayed.
2) Activate the menu item with the button ENTER (11).
The display shows the last show programme
selected ( ...
3) Switch to with the button
firm with the button ENTER. The display shows the
number of the adjusted colour (
4) Select the desired colour with the button
confirm with the button ENTER. The display returns
to and shows the mode (
onds.*
6.1.4 Colour transition
In the transition mode the unit also operates as a
colour radiator, however, there is continuous transition
between the colours. The transition speed can be
adjusted in three steps. The transition mode is only
available in the operating mode 2 (
1) Press the button MENU (9) so many times until
is displayed.
2) Activate the menu item with the button ENTER (11).
The display shows the last show programme
selected ( ...
3) Switch to with the button
confirm with the button ENTER. The display shows
the number of the adjusted speed:
= medium,
4) Select the speed with the button
with the button ENTER. The display returns to
After 10 seconds the mode is shown (
adjustment is effective.*
6.1.5 Manual adjustment of colour,
dimmer and stroboscope
The unit may permanently light up or flash with an
adjustable colour and brightness. The flash frequency
can likewise be adjusted.
Hint: Adjust the colour intended to dominate to maxi-
mum brightness (indication 255) and add the other two
colours. With the dimmer function the brightness of all
LEDs can then be reduced without changing the
adjusted colour.
1) Press the button MENU (9) so many times until
(manual) is displayed. Activate the menu item
with the button ENTER (11). The display now shows
.
2) Press the button ENTER again. The display shows
the value for the colour red. Adjust the brightness of
the red LEDs (indication 0 – 255) with the button
or and confirm with the button ENTER. The dis-
play returns to .
chapter 5.1).
).
or (10) and con-
... ).
or
) after 10 sec-
chapter 5.1).
).
or (10) and
= slow,
= fast.
or and confirm
) and the
3) Switch to
the button ENTER. The display shows the value for
the colour green. Adjust the brightness of the green
LEDs with the button
button ENTER. The display returns to
4) Switch to
the button ENTER. The display shows the value for
the colour blue. Adjust the brightness of the blue
LEDs with the button
button ENTER. The display returns to
5) For fine adjustment of the colour it is possible to
return to a colour with the button
it after pressing the button ENTER.
and
6) For dimming switch to
and confirm with the button ENTER. The display
shows the adjusted brightness value (0 – 255).
Adjust the desired brightness with the button
and confirm with the button ENTER. The display
returns to
7) For activating the stroboscope function switch to
with the button
ENTER. The display shows the adjusted value of
the flash frequency (0 – 255). Adjust the flash fre-
quency with the button
button ENTER. The display returns to
6.2 Interconnecting several
LED-500DX/RGB units
Several LED-500DX/RGB units may be intercon-
nected in order to control all slave units in sync with the
master unit.
1) Connect the DMX OUTPUT (17) of the master unit
via a 3-pole XLR cable (e. g. series MEC-... or
MECN-... from the product range of "img Stage
Line") to the DMX INPUT (18) of the first slave unit.
.
2) Connect the DMX OUTPUT of the first slave unit to
the DMX INPUT of the second slave unit, etc. until
all units have been connected in a chain.
3) Set the slave units to one of the SLAVE modes
( chapter 5.1). Once the control signals from the
master unit are applied to the slave units, the red
LED SLAVE (13) will light up on the slave units.
6.3 Remote control LC-3
The remote control LC-3 available as an accessory
allows to control various functions.
1) Connect the remote control to the jack ONLY FOR
REMOTE CONTROL (16).
2) There must be no DMX signal at the DMX INPUT
(18). Besides, the unit must not be in the manual
adjusting mode (
buttons of the remote control are locked. In this
case switch to another function mode.
*After switching off and on again always the master mode is
activated ( chapter 6.1.1)
with the button and confirm with
or and confirm with the
with the button and confirm with
or and confirm with the
and to readjust
with the button
.
and confirm with the button
or and confirm with the
chapter 6.1.5), otherwise the
GB
.
.
or
or
.*
15