Table of Contents English ................6 Security instructions ..............7 Symbols ..................7 Instructions ................. 7 General remarks ................7 Transport ..................7 Unpacking and delivery content ..........8 Warranty regulations ..............8 Disposal ..................8 Maintenance and Repair ............. 8 Support ..................
Seite 4
11.4 Entsorgung ................16 11.5 Reparatur und Wartung ............. 16 11.6 Technischer Support ..............17 Allgemeine Beschreibung ............17 Installation .................. 17 13.1 Installationsbedingungen ............18 Ethernet-Verbindung ..............18 Stromversorgung ................. 18 Funktionen und Eigenschaften ........... 19 16.1 Lieferumfang ................19 16.2 Anschlüsse und Schnittstellen ..........
Setup Manual - e:cue SYMPL Core S Security instructions Please read the security instructions, provided in a separated manual, carefully. Make sure that the given environmental conditions, mounting and installation prerequisites are met. This manual should be kept at a safe place and in reach of the installation.
Setup Manual - e:cue SYMPL Core S Unpacking and delivery content Unpack the devices and inspect all parts for completeness regarding chapter „2.2 Unpacking and delivery content“. Keep the packaging for use in case of further trans- port. If there is apparent damage to the device or parts are missing from the delivery scope, please contact our Support service.
General device description e:cue SYMPL Core S is a stand-alone engine for e:cue SYMPHOLIGHT with SYMPL Nodes as interfaces. It executes SYMPHOLIGHT shows in small to medium-sized shows and controls all available SYMPL Nodes. As a user interface it utilizes the Action Pad of SYMPHOLIGHT with all usual web browsers.
The pin-assignment of the Ethernet port corresponds to RJ45 standards. You can use every common Ethernet component, like cable, splitters and switches. Never connect more than one SYMPL Core S in factory state to a network. The identical IP addresses will conflict and disturb proper communication.
SD card slot Power supply (Vcc–, Vcc+ left to right) e:net/Ethernet USB 2.0 socket User interface The SYMPL Core S has four LEDs and an Identify button. The four LEDs show the basic states of the SYMPL Core S.
This helps to assign the Node in the Layout in SYMPHOLIGHT. Configuration The configuration of the e:cue SYMPL Core S Node is done via e:cue SYMPHO- LIGHT or over the configuration web interface of the Core S. For configuration with SYMPHOLIGHT see the SYMPHOLIGHT System Manual for details on configura- tion.
Setup Manual - e:cue SYMPL Core S General specifications Oder code AB447060035 Dimensions 71.5 x 90.5 x 62 mm/ (W x H x D) 2.81 x 3.56 x 2.44 in (without fastening clip) Weight 170 g/0.37 lb Power supply 24 V DC on terminal plug wire gauge: 0.25 ...
Setup Manual - e:cue SYMPL Core S Sicherheitshinweise Lesen Sie die Sicherheitshinweise im zusätzlichen Heft sorgfältig. Stellen Sie sich- er, dass die angegebenen Umgebungsbedingungen, Montage- und Installations- voraussetzungen eingehalten werden. Diese Anleitung sollte an einem sicheren Ort in der Nähe des Installationsortes aufbewahrt werden.
Setup Manual - e:cue SYMPL Core S Um Schäden bei Wechsel von Kälte zu Wärme durch Kondensationswasser zu ver- hindern, warten Sie nach dem Auspacken, bis das Gerät die Temperatur am Instal- lationsort angenommen hat. 11.2 Entpacken und Lieferumfang Entpacken Sie das Gerät und überprüfen Sie die Vollständigkeit des Lieferumfanges nach Kapitel „16.1 Lieferumfang“...
+49 (221) 998830-34 support@ecue.com Allgemeine Beschreibung Der e:cue SYMPL Core S ist eine eigenständige Engine für e:cue SYMPHOLIGHT mit SYMPL Nodes als Schnittstellen. Er führt SYMPHOLIGHT-Shows in kleinen bis mittleren Projekten aus und steuert alle verfügbaren SYMPL Nodes. Als Schnittstelle für den Bediener dient das Action Pad in SYMPHOLIGHT über alle gängigen Web-...
Nutzen Sie für die Verbindung zwischen SYMPL Nodes und Cores nur ein Netzwerk innerhalb eines Gebäudes. Stromversorgung e:cue SYMPL Cores sind nicht für den Betrieb über ein Versor- gungsnetz geeignet. Verwenden Sie ein separates Netzteil im Schaltschrank für die 24 V-Gleichspannungsversorgung.
Setup Manual - e:cue SYMPL Core S Funktionen und Eigenschaften SYMPL Cores fürhen eine SYMPHOLIGHT-Show aus. Als Bediener-Schnittstelle di- ent das Action Pad in SYMPHOLIGHT über gängige Web-Browser 16.1 Lieferumfang Im Lieferumfang des e:cue SYMPL dali Node sind: Identcode y e:cue SYMPL Core S...
SYMPHOLIGHT-Server. Damit kann der Core S im Layout zugeordnet werden. 16.3 Konfiguration Die Konfiguration des e:cue SYMPL Core S erfolgt über e:cue SYMPHOLIGHT oder über ein Web-Interface des Core S. Im SYMPHOLIGHT-Manual finden Sie weitere Details zur Konfiguration mit SYMPHOLIGHT. Zertifizierung e:cue SYMPL Core S ist zertifiziert nach EN 55022, EN 55024, 62368-1 Ed.
Setup Manual - e:cue SYMPL Core S Allgemeine Daten Abmessungen 71,5 x 90,5 x 62 mm (B x H x T) (ohne Befestigungsclip) Gewicht 170 g Stromversorgung 24 V= auf Schraubstecker Drahtstärken: 0,25 ... 1,5 mm2, (0,5 mm2 für Litzen mit Aderendhülsen) Leistungsaufnahme max.