Description Of The Machine And Scope Of Delivery; Assembly; Tensioning The Saw Chain; Operation - IKRAmogatec EAS 750F Gebrauchsanweisung

4. Description of the machine and scope of
delivery
(Fig. 1)
1. Mains cable
2. Cable strain relief
3. On/off switch
4. Handle
5. Telescope arm
6. Padded grip
7. Telescope quick-acting lock
8. Motor housing
9. Chain sprocket cover
10. Oil tank cover
11. Multi-function tool
12. Saw chain
13. Guide bar
14. Switch lock
15. Guide bar guard
16. Shoulder belt

5. Assembly

Attention! Only connect the chainsaw to the mains
supply once it has been completely assembled and
the chain tension has been set. Always wear protective
gloves when carrying out work on the chainsaw in order
to prevent injury.
5.1 Assembly of guide bar and saw chain
Carefully unpack and inspect all parts for completeness.
(Fig.1)
• Loosen the fastening bolt for the chain sprocket cover.
(Fig.2)
• Remove the chain sprocket cover.
• Place the chain in the groove of the guide bar as
shown. (Fig.3/Pos. A)
• Insert the guide bar and chain into the mount on the
chainsaw. (Fig. 4) In the process, guide the chain
around the pinion and hang the guide bar in the chain
tensioning bolts.
• Re-mount and hand-tighten the chain sprocket cover
with the fastening bolt. (Fig.5)
Attention! Only tighten the fastening bolt once the
chain tension has been adjusted (see 5.2).

5.2 Tensioning the saw chain

Attention! Always pull out the mains plug be-
fore inspection and adjustment work. Always
wear protective gloves when carrying out work
on the chainsaw in order to prevent injury.
• Loosen the fastening bolt of the chain sprocket cover
a few rotations.
• Adjust the chain tension with a screwdriver at the
chain tensioning screw.
• Clockwise rotation increases the chain tension; anti-
clockwise rotation reduces the chain tension. The saw
chain is correctly tensioned if it can be raised approx.
2 mm in the centre of the guide bar. (Fig.6 + 7)
GB | Operating Instructions
Information regarding the tensioning of the chain
The saw chain must be tensioned properly in order to
ensure safe operation. The chain tension is optimal if the
saw chain can be lifted 2 mm in the centre of the guide
bar. Since the saw chain heats up during the sawing
process, whereby its length changes, you must check
the chain tension at least once every 10 min. and adjust
it as necessary. This applies in particular for new saw
chains. Slacken the saw chain after work is completed,
because it shortens when cooling down. In doing so,
you can prevent damage to the chain.
5.3 Saw chain lubrication
Filling the oil tank (Fig. 8)
• Place the chain saw on a level surface.
• Clean the area around the oil tank cap (Pos.10) and
• Fill the oil tank with saw chain oil. In doing so, make
• Close the oil tank cap (Pos.10).

6. Operation

6.1 Adjusting the telescope length
1. Rotate the locking cap nut (Fig.9) anti-clockwise.
2. The lock is released and can be adjusted to the desi-
3. Then firmly tighten the locking cap nut in clockwise

6.2 Connection to the mains supply

• Connect the mains cable to a suitable extension
• Secure the extension cable against tractive forces
• Connect the extension cable to an earthed safety
Recommendation
Only connect the device to a power source that is pro-
6
Attention! All chain links must lie properly in the
guide groove of the guide bar.
Attention! Always pull out the mains plug before
inspection and adjustment work. Always wear
protective gloves when carrying out work on the
chainsaw in order to prevent injury.
Attention! Never operate the chain without saw
chain oil! The use of the chainsaw without saw
chain oil or with an oil level below the minimum
oil level mark results in damage to the chainsaw!
Attention! Only use special chainsaw oil. The war-
ranty is voided with the use of used oil.
then open it.
sure that no dirt gets into the oil tank so that the oil
nozzle does not clog.
red length by pulling the ends out from one another
to the desired length.
motion.
cable. Make sure that the extension cable is designed
to accommodate the power of the chain saw.
and accidental unplugging as shown in (Fig.10).
socket installed in accordance with regulations. We
recommend the use of a cable in a signal colour (red
or yellow). This reduces the risk of accidental damage
from the chainsaw.