User Manual - Nowsonic Roadtrip 508 Bedienungsanleitung

www.nowsonic.com
Contents
Introduction
Features
Application
Features and Startup
Description of the Inputs
Description of the Multi Effects Processor
Description of the Outputs
Connection examples
Choosing the AMP MODE
Specifications
Scope of supply
Disclaimer
Servicing
Legal information
Introduction
Thank you very much for purchasing the Nowsonic Roadtrip 508! Roadt-
rip 508 is a self-contained, portable PA system featuring 8 input channels
with individual tone controls, an internal FX processor with 16 presets as
well as a Class D power amplifier to feed the integrated speakers. With
its lightweight and ergonomic design the Roadtrip 508 is perfect for si-
tuations where ease and portability are just as important as quality and
flexibility.
Please take your time to read these instructions carefully in order to ope-
rate Roadtrip 508 properly.
Please check the unit after unpacking for any damages. In case the
housing is visibly damaged, please do not operate the unit, but contact
your local dealer from whom you have purchased it.
Features
Roadtrip 508 has the following features:
3-way speaker system with integrated mixer and power amplifier
Maximum output 2 x 250 watts RMS
8 input channels for connecting up to 7 microphones, 3 instru-
ments or 8 line sources (7 x mono, 1 x stereo)
Stereo input channel for connecting an iPod or CD player
Mono channels with balanced inputs (XLR and 1/4" TRS jack)
Internal Bluetooth receiver for wireless reception of audio signals
2 band equalizer per channel
Phantom power switchable for all microphone inputs
Integrated Multi-FX processor with 16 presets
Send control per channel for a monitor output
Balanced output (XLR) for connecting an external subwoofer
Compact and road-proof enclosure
Application
Roadtrip 508 is recommended for the following applications:
sound reinforcement for small concerts as a powered FOH system
sound reinforcement on stage as a powered multichannel
monitoring system
Combined use for active FOH and stage monitoring
Mixer and/or monitoring system for rehearsal and practicing at
Features and Startup
Roadtrip 508 is divided into three areas:
8-in-2 mixer with 7 mono channels, one stereo input and an internal
FX processor
2-channel Class D power amplifier for driving the integrated 3-way
speakers and/or external monitors/subwoofer
Stereophonic 3-way speaker system
Roadtrip 508 is a self-contained system which integrates the mixer
and the Class D amplifier in the same enclosure while the separate
modules of the 3-way speaker system are mounted on the front and
back of the mixer/amplifier unit for transport. Before using Roadtrip
508 you first have to detach the speaker modules and hook up the
mixer/amplifier unit.
Proceed as follows:
1) Place Roadtrip 508 on solid ground.
2) Release the buttons on both sides of the handle on top of the
main module: Now you can remove the two speaker modules to
the side.
3) If required place the speaker modules and/or the mixer/amplifier
unit on speaker stands (not included): you will find a standard pole
socket (35 mm) on the bottom of every module.
4) Connect the LEFT/MAIN and RIGHT/MON outputs in the OUTPUTS
section of the mixer/amplifier unit with the jacks on the rear of the
speaker modules using the supplied speaker cables (5m).
NOTE: Route cables so that performers, production crew, and au-
dience will not trip and topple the speakers over.
5) Next connect your external sources like microphones, instruments
and/or line devices with the Combo and stereo inputs on the front
of the mixer/amplifier unit. Please note that the input cables are
not supplied with the unit.
6) Connect the mixer/amplifier unit with the mains outlet using the
supplied IEC power cord.
7) Make sure to completely turn down all volume controls on the
mixer/amplifier unit before powering up Roadtrip 508.
5
ROADTRIP 508
GB

User manual

home