Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Smoke Alarm Device
Operation- and installation manual
① ① ① ① Safety advice – Please consider:
1. Do not use any rechargeable batteries or mains adapter for powering.
2. A loud and shrill test tone will sound during the function test. Keep a safety dis-
tance of 50 cm between your ear and the smoke alarm device.
3. Smoke alarm devices may not be painted.
4. The smoke alarm device may not
a. Steamy, damp areas like bathroom or kitchens
b. near fire places
c. in areas with temperatures lower then –10°C or higher then 60°C
d. near air-conditioner or air circulation units
e. in tapered ceilings
f. Keep at least 50 cm away from all light fittings
g. the smoke alarm device
5. The underlined waste container on the reverse side of the product is an advice
not to dispose the detector in the domestic waste.
Attention:
Danger of explosion, during incorrect changing of the battery.
Only exchange to an equal accredited type of battery.
1
① ① ① ①
4d
② ② ② ② Installation and commissioning:
1. Choose the installation location (room ceiling is recommended):
a. Best location in the centre of the room, at least 50 cm space to the nearest
wall.
b. Minimum space to nearest lamp 50 cm.
If using the adhesive pad: Check the surface of the ceiling to make sure that the ad-
hesive pad sticks tightly to it.
2. Keep a minimum distance of 50 cm from all conducting electrical cables.
Make sure that there are no electricity cables at location.
3. Make sure not to pollute the smoke alarm device when drilling the holes
(*if installing the smoke alarm device with an adhesive pad see chapter 13 "Op-
tional Accessories").
4. Drill two 6 mm holes (with a gap of 67 mm if using two screws)
(You can use the smoke alarm device base as a hole template).
5. Place the included raw plugs into the drill holes.
6. Tighten the detector base with the included screws to the ceiling.
7. Connect the battery (watch the polarity) and place it into the intended bracket of
the smoke alarm device.
8. Attach the smoke alarm device to the base and tighten it by turning the detector
clock wise. (Only possible if a battery is installed).
9. Check if the detector LED flashes.
10. Check the functionality by pressing the test LED conductor pole for at min. one
second.
A warning beep sounds if the detector is operational. If no beep sounds then
the detector is not functional. In this case check the battery and replace it.
If still no beep sounds after pressing the test LED conductor pole again then the
detector is defect and needs to be exchanged.
1a
② ② ② ②
6
V 1.7 03.07.2017
HDv 300X OS
HDv 300X OS
HDv 300X OS
HDv 300X OS
not be placed at the following locations:
not
not
HDv 300X OS
HDv 300X OS
HDv 300X OS
HDv 300X OS
is only approved for indoor use
2
4e
1b
7
③ ③ ③ ③ Product characteristics
Battery powered, radio curable smoke alarm device for detection and alarming in domestic
and small system applications, due to the EN 14604:2005:
• Reliable fire detection through precise adjustment of the release characteristics
• Outstanding operating safety by intelligent analysis of measuring chamber signal
• A visual and auditable low battery condition is signalled for 30 days
• The detector is equipped with a condition / contamination indicator regarding to UL
guidelines.
• The acoustic alert is made by an integrated piezo alarm-sounder (min 85 dB)
• False alarm reduced due to the high performance measuring chamber and
temperature variability (but no heat detector)
• The LED conductor pole is used as "Alarm-Mute-Test-Button"
• The smoke alarm device
The function indicates a local fire alarm within the last 24 hours
• Radio communication to further detectors is possible with an optional radio module
868 MHz (Order No.: 30933) or to a radio- fire control panel (Order No.: 32487)
by the optional radio module 433 MHz (Order No.: 32488)
• The smoke detector can be connected to an EIB or for connecting external
signallers by the optional radio-module (Order No.: 30942)
• For detection and alarming in caravans.
• The pack includes the smoke alarm device with detector base, one battery, two
screws with anchors for mounting and this manual.
3
4a
4f
4g
④ ④ ④ ④ Place of installation
The smoke alarm device performs best when installed on the ceiling in the centre of the
room. If this is not possible, ensure the detector is at least 50 cm from the wall.
⑤ ⑤ ⑤ ⑤
Adhesive pad
The detector base can be attached to the ceiling via one or two included screws and
anchors or with the double sided adhesive pad (Order-no.: 32587). Check the condition
of the corresponding surface before fitting the detector to assure a firm hold.
Check the surface condition of the ceiling before use of the double sided adhesive pad.
It must be suitable for durable bonding and bearing strength (test bonding if necessary).
Pull of the protection film on one side of the pad and stick the pad tightly to the centre
of the detector base. Next remove the film of the other side, tighten the detector base
firmly to the ceiling and continue as described in chapter 2 step 7.
2
3
8
9
Manual-No.: 53688
HDv 300X OS
HDv 300X OS is
HDv 300X OS is
equipped with an Alarm Memory function.
HDv 300X OS is
HDv 300X OS is
4b
5 (Img. label)
Minimum protection
Optimale equipment
Special equipment
To be sure that you are woken up by smoke alarm at
night the smoke alarm device should be placed in the
bedrooms/hallway as a minimum protection. In
houses with several floors one smoke alarm device
should be placed in each hall of the floor. Further
installation guidelines can be found in the DIN 14676
standard.
4
10
4c
5
11
Page 3 of 4
Werbung
