Product Description; What Do You Need - Widek Qibbel Gebrauchsanleitung

PRODUCT DESCRIPTION

Congratulations on the purchase of your Qibbel bike seat. You have not only
chosen a seat that you can create entirely to your own liking, you have also
chosen a safe seat that will bring you and your child lots of cycling pleasure.
The seat can be adjusted stepwise so that you can always choose the most
comfortable position for your child. (see instructions for use)
The seat is suitable for children of approximately nine months to six years of
age, who weigh at the maximum 22 kg. Only use the seat once your child is
able to sit without assistance for the entire bicycle ride. Read these installation
instructions carefully before installing the seat. Please address any questions
you have to your supplier.
The seat is available in two versions, for attachment to the carrier or to the
frame. You choose the right attachment for your bike to accompany the basic
element.
You can choose the carrier attachment if the carrier meets the requirements
laid down in the NEN 14872 standard. The width of the rack should be between
12 and 17 cm, the diameter of the frame between 8 and 16 mm and the
load-bearing capacity should be at least 25 kg. You can choose the
attachment for the frame if this has a round or oval cross section of 22 to 40
mm. This is also the case for many electric bikes.
Two-year guarantee: We give a two-year guarantee on manufacturing and/
or material defects. The guarantee starts on the date of purchase, please keep
your purchase receipt.
In addition to these seat installation instructions, you can also
SEAT INSTALLATION INSTRUCTIONS
Follow these instructions to safely and correctly install the seat to your bike.
Figure 1M | Tools
To mount the Qibbel seat, you need the following tools:
Standard Allen keys 2.5, 4, and 6

WHAT DO YOU NEED?

Figure 2M | For a safe child's seat you require
1 Rear seat basic element
2A Carrier attachment
or
2B Frame attachment and
2C Frame attachment bracket
2D
Spacer frame attachement (option)
3A
Styling set Basic rear (foot straps/ armrests)
or
3B
Styling set De-luxe rear (foot straps/ armrests/ seat upholstery)
Figure 3M | You can enhance your Qibbel seat with the following accessories
4 Lock
CARRIER ATTACHMENT
To be able to attach the seat to your carrier you require, in addition to the rear
seat basic element (1), just 1 part, the carrier attachment (2A). No tools are
needed.
Figure 4Mb | Carrier attachment
pull out the red knob on the front of the seat. Then slide the carrier attachment
© 2014 Widek BV Krimpen aan den IJssel, The Netherlands.
under the seat from the rear, in a circular motion. Ensure that the securing
strap is at the front of the attachment. Slide the attachment until it reaches
attachment by pressing the red knob on the front.
Then attach the seat to the carrier by adjusting the clamping mechanism to
the width of the carrier. To increase the width, turn the adjuster anti-clockwise.
clockwise. Ensure that the hooks are correctly positioned around the sides of
the carrier.
Figure 4Mc | Check whether the seat is correctly mounted
Check that the centre of gravity of the seat is no more than 10 cm behind
the rear axle of the bicycle. Place your child in the seat and check that there
your child to sit comfortably. To change the position of the seat, loosen the
clamping mechanism of the attachment block and move the seat forward
or backward along the carrier. Then tighten the clamping mechanism as
tightly as possible.
Figure 4Md | Additional safety
strap around the frame. When you take the attachment from the packaging,
open the buckle by pressing the three-point fastener (on the side and on the
top). Fix the strap around the frame of the bicycle and close the buckle.
Figure 4F | Additional wheel protectors
Use the additionally supplied transparent wheel protectors to extend the
barrier between the wheel and the legs of the child. Slide the extension over
the transparent foot support guard until it clicks into place. This increases the
safety of the child while cycling.
FRAME ATTACHMENT
To attach the seat to the frame of your bicycle, you need three components:
The rear seat basic element (1), the frame attachment (2B) and the frame
attachment bracket (2C).
Figure 5Ma | Frame attachment
Mount the frame attachment. Ensure that the round holes are at the top.
diagonally and evenly. Suitable for round and oval saddle tubes Ø 22-40 mm.
Using the movable inner ring, adjust the angle of the clamp to the angle of
the frame to ensure that the seat is positioned horizontally above the rear
wheel. The red knob at the front is used to unlock the seat attachment.
T T p i p i f I : f I : y y o o u u w w a a t n t n o t o t u u s s e e h t h t
purchase an additional frame attachment. (2B) purchase an additional frame attachment. (2B)
Figure 5Mb | Checking the frame attachment
Check whether the attachment has been installed at the right height by
clicking the frame attachment bracket into the frame attachment. First
remove the retaining ring from the bracket. The bracket must be positioned
horizontally above the rear wheel, the distance between the bracket and the
rear wheel must be at least 10 cm. If this is not the case, you must move the
attachment or change its angle by adjusting the movable inner ring.
Tip: If the space between the bottom of the bracket for the frame Tip: If the space between the bottom of the bracket for the frame Tip: If the space between the bottom of the bracket for the frame Tip: If the space between the bottom of the bracket for the frame Tip: If the space between the bottom of the bracket for the frame
attachment and carrier is less than 10 cm, mount the spacer
frame attachment. (2D)
© 2014 Widek BV Krimpen aan den IJssel, The Netherlands.
e e s s e e t a t a o o n n m m o o e r e r h t h t a a n n o o n n e e b b k i k i , e , e