Pairing The Wireless Subwoofer With The Soundbar; Automatic Pairing; Manual Pairing; General Operation - vogel's NEXT 8365 Installations- Und Betriebshandbuch

3.4 Pairing the Wireless subwoofer with the Soundbar

Ex factory the Wireless subwoofer and Soundbar are paired.

Automatic pairing

1
Plug the dedicated SoundMount power cable into the
Soundbar.
2
Plug the subwoofer into the mains sockets.
3
Press the button on the Soundbar or on the remote
control to switch the Soundbar ON.
> The subwoofer and soundbar will automatically pair
within 30 seconds.
> When the subwoofer is pairing with the soundbar, the
Indicator will flash rapidly.
> When the subwoofer is paired with the soundbar, the
Indicator will light up constantly.
> During STANDBY mode, the subwoofer Indicator will
go off and flash slowly.

Manual pairing

1
Plug the dedicated SoundMount power cable into the
Soundbar.
2
Plug the subwoofer into the mains sockets.
3
Make sure that the Soundbar is in STANDBY mode.
4 Press and hold the Wireless pairing button on the
bottom of the subwoofer for a few seconds.
> The subwoofer will enter the pairing mode and the
Indicator will blink quickly.
5
Press the button on the Soundbar or on the remote
control to switch the Soundbar ON.
> After the wireless connection succeeds, the Indicator
will light up constantly.
> If the Indicator still blinks or does not blink at all, the
wireless connection has failed.
• Unplug the cable of the subwoofer.
• Reconnect the main cable after 3 minutes.
Repeat steps 1 - 5.
•
Notes!
If the wireless connection fails again, check if there is a
•
conflict or strong interference (for example, interference
from an electronic device) around your location.
Remove these conflicts or strong interferences and
repeat the above procedures.
• The subwoofer must be within 6m of the Soundbar in an
open area.
• If the Soundbar is not connected with the subwoofer
and it is in On mode, then the message
'CHECK SUBWOOFER' will show on the display and the
Indicator on the bottom of the subwoofer will blink.
Repeat steps 1 - 5 above to pair the subwoofer to the
Soundbar.
8

4. GENERAL OPERATION

4.1 Using the remote control of the TV

When the HDMI ARC socket of the Soundbar is connected
to the HDMI ARC socket of the TV via the HDMI cable and
the CEC function on the TV is activated in the setup menu of
the TV, you can use the remote control of the TV to
control the SoundMount (Soundbar and subwoofer).
• When the TV is switched ON, the SoundMount (Sound-
bar and subwoofer) will automatically switch ON.
• When the TV is switched to OFF / STANDBY, the Sound-
Mount will automatically switch OFF (to STANDBY).
• When the SoundMount is ON, the sound volume can be
controlled with the VOLUME - / VOLUME + and MUTE
buttons on the remote control of the TV.
Note!
• To make it possible to control the SoundMount with the
remote control of the TV, it is important that the HDMI
CEC (Consumer Electronics Control) function is activated
in the setup menu of the TV.
This function has a different name for each TV brand:
Anynet (Samsung), Aquos Link (Sharp), Bravia Sync
(Sony), Regza Link (Toshiba), Simplink (LG),
Viera Link Panasonic), EZ-Sync (JVC), Easylink (Philips),
Netcommand (Mitsubishi).
The internal TV speakers will automatically be disabled
the moment the TV is switched ON and the Soundbar is
switched on automatically.

4.2 Using the supplied (Soundbar) remote control

When the HDMI ARC socket of the Soundbar is connected
to the HDMI ARC socket of the TV via the HDMI cable and
the CEC function on the TV is activated in the setup menu of
the TV, you can use the remote control of the TV to
control the SoundMount (Soundbar and subwoofer).
In this case, you only need the supplid (Soundbar) remote
control for initial settings of personal preferences (TREBLE,
BASS, brightness level of Soundbar display) and for
controlling special functions like Bluetooth audio streaming.
In case the Soundbar and the TV are connected via an
optical link, the supplied (Soundbar) remote control also
must be used to control the SoundMount TV volume, source
selection, etc..
It is not possible to control the sound volume with the
remote control of the TV. Internal TV speakers must be
switched off manually. See the setup menu of the TV.

Standby / ON

When you first connect the Soundbar to the mains socket,
the Soundbar will be in STANDBY mode and the STANDBY
Indicator lights red.
• Press the button on the Soundbar or on the remote
control of the TV to switch the Soundbar ON.
Press the button again to switch the Soundbar back
•
to STANDBY mode.
> The Standby Indicator will light up red.
Disconnect the mains plug from the mains socket if you
•
want to switch the Soundbar off completely.
Note!
• When the Soundbar is idle for approximately 15 minutes,
it will automatically switch to STANDBY mode.