Technical Specifications - EE link CLONIX 4 RTE Gebrauchsanleitung

Therefore it will be possible to remotely program a
large number of additional transmitters, or for example,
replacement transmitters for those which have been
lost, without making changes directly to the receiver.
Cloning by replacement is used to create a new
transmitter which takes the place of the one previ-
ously memorised in the receiver; in this way the lost
transmitter is removed from the memory and will no
longer be usable
Using clones when there is more than one receiver
(as in the case of communal buildings), and especially
when a distinction is to be made between clones to be
added to or replaced in individual or collective receiv-
ers, could turn out to be rather difficult. The CLONIX 4
RTE receiver cloning system for communal buildings
makes it particularly easy to solve the problem of clone
storage for up to 250 individual receivers.

2) TECHNICAL SPECIFICATIONS

Frequency...............................................:433.92MHz
Working temperature..............................:-20 / +55°C
Coded by means of...............:Rolling-code algorithm
No. combinations........................................:4 milliard
Dimensions..................................................:see fig.6
Power supply.................................:230V ±10% 50Hz
Antenna impedance..........................:50Ohm (RG58)
Relay contact ............................................:4 x 16A
Max no. radio transmitters to be memorised.:..........128
Max absorption on 12V..................................:100mA
2.1) CONNECTIONS See Fig.7
3) ANTENNA INSTALLATION
Use an antenna tuned to 433MHz.
For Antenna-Receiver connection, use RG8 coaxial
cable.
The presence of metallic masses next to the an-
tenna can interfere with radio reception. In case of
insufficient transmitter range, move the antenna
to a more suitable position.
4) PROGRAMMING
The TRANSMITTERS can be memorised in manual
mode or by means of the universal palmtop Programmer,
which allows installations to be carried out in "common
receivers" mode and managed by means of the EEdbase
software for complete installation database.
4.1) Manual memorisation of transmitters, see fig.1-2
In the case of standard installations, which do not require
advanced functions, the transmitters can be memorised
manually, making reference to Fig.2.
1) If you wish the transmitter to activate output 1, press
the SW1 button, whereas if you wish the transmitter
to activate output 2, press the SW2 button.
2) If you wish to use functions other than those for
monostable activation, make reference to Fig.1
and 2.
INSTALLATION MANUAL
3) When the DL1 led blinks, press hidden key P1
on the transmitter, and the DL1 led will stay on
permanently.
Note: Hidden key P1 looks different depending on
the transmitter model.
4) Press the transmitter key to be memorised, and
the DL1 led will start blinking again.
5) To memorise another transmitter, repeat steps 3)
and 4).
6) To come out of the memorisation mode, wait until
the led is completely switched off.
IMPORTANT NOTE: ATTACH THE ADHESIVE KEY
LABEL TO THE FIRST MEMORISED TRANSMIT-
TER (MASTER).
In the case of manual programming, the first transmit-
ter assigns the key code to the receiver; this code is
necessary in order to carry out subsequent cloning of
the radio transmitters.
4.2) Transmitter storage via radio in self-learning
mode
This mode is used to memorise a transmitter without
having to access the receiver.
The first transmitter is to be memorised in manual
mode.
a) Press hidden key P1 on the transmitter already memo-
rised.
b) Press key T on the transmitter already memorised,
which is also to be attributed to the new transmit-
ter.
c) Within 10 sec., press key P1 on the new transmitter
to be memorised.
d) Press key T to be attributed to the new transmit-
ter.
e) To memorise another transmitter, repeat the pro-
cedure from step (c) within a maximum time of 10
seconds, otherwise the receiver exits the program-
ming mode.
f) To copy another key, repeat from step (a), having
waited for the receiver to exit the programming
mode (or after disconnecting the receiver from the
power supply).
5) RADIO-TRANSMITTER CLONING
Rolling-code cloning.
Make reference to the instructions for the universal
palmtop programmer and to the CLONIX program-
ming guide.
6) ADVANCED PROGRAMMING: COLLECTIVE
RECEIVERS
Make reference to the instructions for the universal
palmtop programmer and to the CLONIX program-
ming guide.
7) MANUAL PROGRAMMING OF CARDS AND
CODES FROM THE KEYPAD (WIEGAND 26 standard),
see Fig. 3-4
ENGLISH
CLONIX 4 RTE - Ver. 03- 9