Transportation And Storage; Cleaning And Maintenance; Technical Details - Royal Catering RCZK-1200E Bedienungsanleitung

6. After having produced the amount of cotton candy you need, please do not switch off the device but
rather clean the cotton candy turner with water first. Keep pouring water into it while the head of the
cotton candy turner continues to rotate. After that you can switch off the machine. The device should
be cleaned after each use.
X. OPERATION (only for model RCZK-420-W)
1. Push the On-button and keep the machine running for 1-2 minutes. Now check if the device is ready
for operation (the standing position of the machine needs to be adjusted in the event of extreme
vibration).
2. Work can be started after the cotton candy turner is properly warmed up - add a measuring spoon of
granulated sugar into the centre of the cotton candy turner.
3. Cotton candy starts being produced almost immediately after adding the sugar. Take the bamboo stick,
move it along the inner surface of the bowl and turn the stick around while doing so. As a result
you will get the typical cotton candy shape. (The bamboo stick may be cleaned with a dry cloth. It is
recommended that the stick is not entirely smooth, cotton candy sticks better to a rough bamboo
stick).
4. After having produced the amount of cotton candy you need, please do not switch off the device but
rather clean the cotton candy turner with water first. Keep pouring water into it while the head of the
cotton candy turner continues to rotate. After that you can switch off the machine. The device should
be cleaned after each use.
XI. NOTES
1. Keep minors away from the machine.
2. The electric cable must not come near the hot surface of the machine. Please ensure that the electric
cable and the connector plug do not come into contact with water or any other liquids. DO NOT use
the device if the cable or the connector plug is damaged.
3. Please DO NOT touch the surface of the machine while it is in operation. DO NOT move the machine
while in operation.
4. Never touch the plug or cable with wet hands.
5. The temporary motor power of the device amounts to 80%. It is best to avoid extremely long usage
periods. In order to prolong the life of the machine the engine should rest for 20 minutes after every
hour of usage.
6. Before cleaning make sure that the plug is pulled out.
7. If the cotton candy turner doesn't make any cotton candy, please turn off the device and remove burnt
sugar with soft cloth.
XII. TECHNICAL DETAILS
Models RCZK-1200E | RCZK-1200-W | RCZC-1200E | RCZC-1200-W | RCZK-1200XL | RCZC-1200XL:
Model: RCZK-420-W:
12
XIII. TRANSPORTATION AND STORAGE
Shaking, crashing and turning upside down of the device should be prevented when transporting it. Store it
in a properly ventilated location with dry air and without any corrosive gas.
XIV. CLEANING AND MAINTENANCE
• Disconnect from electricity when cleaning equipment.
• Use cleaner without corrosive substances to clean surface.
• Dry all parts well after cleaning before the device is used again.
• Store the unit in a dry, cool location, free from moisture and direct exposure to sunlight.
ATTENTION: Clean the device after use, regardless of whether it was operated only once or a number of
times. For efficient head cleaning, after use, pour approximately 150 ml of water (approximately 100 ml if
using RCZK-420-W) into a hot and spinning head. The evaporating water will clean the interior of the head.
Switch the machine off. Once the head has cooled down, use a soft, damp cloth to wipe it clean. Failure to
follow these instructions may result in a build-up of caramelised sugar, leading to defective operation of the
machine (candy floss will not spin, in extreme situations the head may be permanently damaged).
The user shall be responsible for all damage resulting from a failure to follow these instructions.
ATTENTION: When replacing the drive belt, remember to mount it the right way around - as shown on the
photograph below (the belt teeth should be on the inside):
XV. REGULAR CONTROL OF THE DEVICE
Regularly control whether the device is damaged. If it should be damaged, please stop using it immediately
and contact your customer service to solve the problem.
What to do in case of a problem?
Please contact your customer service and prepare following information:
• Invoice number and serial number (the latter is to be found on the technical plate on the device).
• If relevant, a picture of the damaged, broken or defective part.
• It will be easier for your customer service clerk to determine the source of the problem if you give a
detailed and precise description of the matter. Avoid ambiguous formulations like "the device does not
heat", which may mean either that it does not heat enough or that it does not heat at all. The more
detailed your information, the better the customer service will be able to solve your problem rapidly
and efficiently!
CAUTION: Never open the device without the authorization of your customer service. This can lead to a
loss of warranty!
Rev. 01.08.2017 Rev. 01.08.2017 13