Sentera RSMFX-2R Montage- Und Bedienungsanleitung Seite 10

RSMFX-2R
HOLDING REGISTERS
Data type
1 Device slave address unsigned int. Modbus device address
2 Modbus baud rate unsigned int. Modbus communication baud rate
3 Modbus parity mode unsigned int. Parity check mode
4 Device type unsigned int. Device type (Read only)
5 HW version unsigned int. Hardware version of the device (Read only)
6 FW version unsigned int. Firmware version of the device (Read only)
7
8 Output 1 overwrite (T) unsigned int.
9 Output 2 overwrite (rH) unsigned int. Enables the direct control over the rH output
10 Output 3 overwrite (CO ) unsigned int. Enables the direct control over the CO
2
11 Output 1 type (T) unsigned int. Select analog / digital output type
12 Output 2 type (rH) unsigned int. Select analog / digital output type
13 Output 3 type (CO ) unsigned int. Select analog / digital output type
2
Minimum temperature
14 unsigned int.
range
Maximum temperature
15 unsigned int.
range
Minimum relative
16 unsigned int.
humidity range
Maximum relative
17 unsigned int.
humidity range
18 Minimum CO range unsigned int.
2
19 Maximum CO range unsigned int.
2
Minimum temperature
20 unsigned int. Minimum temperature alarm value
alert
Maximum temperature
21 unsigned int. Maximum temperature alarm value
alert
Minimum relative
22 unsigned int. Minimum relative humidity alarm value
humidity alert
Maximum relative
23 unsigned int. Maximum relative humidity alarm value
humidity alert
24 Minimum CO alert unsigned int. Minimum CO
2
25 Maximum CO alert unsigned int. Maximum CO
2
26 LED indication unsigned int. LED indication related to one of the parameters
Internal voltage source
27 unsigned int. Selection of internal voltage source for PWM output 1
selection Output 1 (T)
Internal voltage source
28 unsigned int. Selection of internal voltage source for PWM output 2
selection Output 2 (rH)
Internal voltage source
29 unsigned int. Selection of internal voltage source for PWM output 3
selection Output 3 (CO )
2
Modbus network resistor
30 unsigned int.
termination (NBT)
Output 1 overwrite
31 unsigned int.
value (T)
Output 2 overwrite value
32 unsigned int.
(rH)
Output 3 overwrite value
33 unsigned int.
(CO )
2
34 Active level unsigned int.
35 Standby level unsigned int.
36 Modbus registers reset unsigned int.
CO module self
2
37 calibration (ABC logic) unsigned int.
algorithm
38—40
Um mehr zu erfahren über Modbus und über serielle Schnittstelle, folgen Sie diesem Link:
MIW-RSMFX-2R-DE-000 - 05 / 04 / 18
MULTIFUNKTIONALER
RAUMTRANSMITTER
Description
Reserved, returns "0"
Enables the direct control over the temperature
output.
2
Minimum value of the temperature range; cannot be
set higher than max. temperature range minus 5ºC
Maximum value of temperature range; cannot be set
lower than min. temperature range plus 5ºC
Minimum value of the rH range; cannot be set higher
than max. rH range minus 5 %
Maximum value of rH range; cannot be set lower than
min. rH range plus 5%
Minimum value of the CO range; cannot be set higher
2
than max. CO range minus 100 ppm
2
Maximum value of CO range; cannot be set lower
2
than min. CO range plus 100 ppm
2
alarm value
2
alarm value
2
Set device as ending the line or not by connecting
NBT
Overwrite value for output 1. Active only if Holding
register 8 is set to 1
Overwrite value for output 2. Active only if Holding
register 9 is set to 1
Overwrite value for output 3. Active only if Holding
register 10 is set to 1
The ambient light level above which 'Active' is
indicated in input register 6
The ambient light level below which 'Standby' is
indicated in input register 6
Resets Modbus Holding registers to default values.
When finished this register is automatically reset to
'0'
Enables or disables the CO module self-calibration
2
algorithm. If enabled, the sensor will typically reach
its operational accuracy after 24 hours of continuous
operation. The sensor will maintain its accuracy given
that it is exposed to a reference level of 400 ppm CO
at least once in a 7 day period
Reserved, return "0"
www.sentera.eu
Zurück zu Inhaltsverzeichnis
Data
1—247
0—6
0—2
RSMFX-2R = 1083
XXXX
XXXX
0—1
0—1
output 0—1
1—3
1—3
1—3
0 — (Max. range — 50)
(Min. range + 50) – 500
50 — (Max. range — 50)
(Min. range + 50) – 850
0 – (Max. range — 100)
(Min. range + 100) – 2.000
Min. temperature range —
Max. temperature alarm
Min. temperature alarm —
Max. temperature range
Min. relative humidity range —
Max. relative humidity alarm
Min. relative humidity alarm —
Max. relative humidity range
Min. CO range — Max. CO
2
alarm
Min. CO alarm — Max. CO
2
range
1—3
0—1
0—1
0—1
0—1
0—1.000
0—1.000
0—1.000
0—32.000
0—32.000
0—1
0—1
2
http://www.modbus.org/docs/Modbus_over_serial_line_V1_02.pdf
Default Values
1
0 =
1 =
2 =
2 3 =
4 =
5 =
6 =
0 =
1 1 =
2 =
0x0100 = HW version 1.00
0x0100 = FW version 1.00
0 = Disabled
0
1 =
0 = Disabled
0
1 =
0 = Disabled
0
1 =
1 = 1—10 VDC
1 2 = 0—20 mA
3 =
1 = 1—10 VDC
1 2 = 0—20 mA
3 =
1 = 1—10 VDC
1 2 = 0—20 mA
3 =
0 100 =
500 500 =
50 200 = 20,0 % rH
850 850= 85,0 % rH
400 1.000 = 1.000 ppm
2.000 2.000 = 2.000 ppm
0 100 =
500 500 =
50 200 = 20,0 % rH
850 850 = 85,0 % rH
400 400 = 400 ppm
2
2.000 2.000 = 2.000 ppm
2
1 = temperature
1 2 =
3 =
0 =
0
1 =
0 =
0
1 =
0 =
0
1 =
0 = NBT disconnected
0
1 = NBT connected
0 =
0
1.000 =
0 =
0
1.000 =
0 =
0
1.000 =
100 1.000 =
10 10 =
0 = Idle Reset Modbus
0
1 = registers
0 = Disabled
1
1 =
10 - 11
4.800
9.600
19.200
38.400
57.600
115.200
230.400
8N1
8E1
8O1
Enabled
Enabled
Enabled
PWM
PWM
PWM
10,0 °C
50,0 °C
10,0 ºC
50,0 ºC
rH
CO
2
3,3 VDC
12 VDC
3,3 VDC
12 VDC
3,3 VDC
12 VDC
0 %
100 %
0 %
100 %
0 %
100 %
1.000 lx
10 lx
Enabled