Tommee Tippee perfect prep Gebrauchsanweisung Seite 3

WARNING LIGHTS
CHANGE
J
FILTER
WATER TANK
K
HOT
WATER LEVEL
L
LOW
DE-CALC /
M
DE-SCALE
CLEANING
N
MODE
As with any other method of making up a feed, it's essential that good hygiene practices are observed in the use and maintenance of your Perfect
Prep machine. Ensure your hands and all surfaces that come in to contact with the machine and its components are clean, and that the unit is
away from direct sunlight and heat sources.
REGULAR CLEANING: For hygiene and safety reasons you should clean your unit on a regular basis. We recommend you carry this out at least every 4
weeks, whenever you replace your filter or if the machine has been unused for a period of 7 days.
1
2
Place a container under the Plug in the unit, the tank empty
dispenser spout to capture the water warning light will illuminate.
used to clean the system (ideally at
least 1.8 litre capacity).
5 6
Allow the cycle to fully complete with
Press the cleaning mode button and
boiled water dispensing into the
hold for 2 seconds. The cleaning
container that you placed underneath
mode light will illuminate.
during step 1.
Handling the filter
9a
9b
by the top only:
• Remove the filter from the
packaging
• Remove sticker from the top of filter
• Fill a bowl with cold tap water
• Fully submerge the filter in the water
• Gently agitate until the bubbles stop
Without removing the hopper from the machine and still holding the filter
by the top, place the filter in the hopper, ensuring it locks in to place.
ACTION BUTTONS
CLEANING
O
MODE
FILTER
P VOLUME
RESET
DE-CALC /
Q
DE-SCALE
SET UP
3
4
Fill the water tank with freshly Wait for the tank empty warning
boiled water. light to go out. The water tank hot
light will illuminate.
8
7
The tank empty warning light will Discard the contents from the
illuminate once the water has container used and place it back
flushed through the system. under the dispenser spout.
10 11
Fill the hopper with cold water. Wait for the tank empty warning
light to go out.
13
12
FILTER
VOLUME
RESET
Set the dial to 120ml/ 4 fl oz with container
Press the filter volume reset button
under the dispenser spout.
for 2 seconds to clear the memory.
Press the start/stop button. A red
light will flash.
Before each use you must ensure that your water tank is above the minimum fill mark.
Always use cold water when filling the water tank, other than when cleaning.
1
Check the water level and Turn the dial to select the feed size
regularly top up when necessary you require (120–330 ml / 4–11 fl
with cold water. When filling the oz).
tank with water, ensure the hopper
is in place.
5 6
Carefully remove the bottle from the Screw the sterilised milk storage lid Shake well until the formula powder
stand and measure the correct onto the bottle and ensure that the has dissolved.
number of formula scoops into the lid is tight. Be careful when handling
bottle. hot liquid.
10 11
Wait whilst the remainder of water is Always check that the amount For your child's safety always check
dispensed. Once completed, there dispensed is consistent with the food temperature before feeding by
will be a double beep and the green size of feed you have selected on testing on a sensitive part of your
light will change to solid. the dial (by adding formula, your skin.
feed will appear larger than the feed
size chosen). Add the sterilised teat,
screw ring and hood and shake.
14 15
The appliance will dispense an Press the start/stop button again.
amount of hot water. A green light will flash and an amount
of water will be dispensed to finish
the cycle. Discard the contents of the
container. Fit the bottle stand.
Your machine is now ready to use.
USAGE
2 3
Position your sterilised bottle under Press the start/stop button.
The light will change to solid red
the spout. Adjust bottle stand if A red light will flash and a volume
and there will be a double beep to
necessary (bottle neck should sit of hot water is dispensed into your
indicate the end of the first stage.
close to the spout). bottle. You will need to make up your feed
within 2 minutes.
7
Remove the milk storage lid and Press the start/stop button again.
replace your bottle onto the bottle The red light will go out and the
stand. green light will flash. If this button is
not pressed within 2 minutes of the
hot water being dispensed a long
beep will sound. If the alarm sounds
you should discard the feed and
repeat the process from step 1.
12 13
Your bottle is now ready to serve.
Make sure you discard any
unwanted feed as per the formula
manufacturer's recommendation.
4
9