Before First Use; Operation Of The Appliance; Setting The Timer - Inventum VKI3010ZWA Gebrauchsanweisung

3

before first use

Before using the induction cooker for the first time, proceed as follows: Unpack the induction cooker and remove all packaging
material. Keep the packaging (plastic bags and cardboard) out of the reach of children. After unpacking the appliance, check it for
external damage that may have occurred during transport. If still present, remove the protective film from the glass plate. Clean
the glass ceramic plate with a moist cloth. Check that the voltage stated on the information plate matches the voltage used in your
region.
For the installation of the cooker you must observe the instructions in section 7.
4

operation of the appliance

Only use pans that are suitable for an induction cooker and have the correct size with a cross-section from 15 to 20 cm.
The induction cooker works by means of electronic sensors that are operated by touching the touch control and/or control key. At
each touch of a touch control or control key, you can hear a sound signal. Make sure the operating section is always clean and dry.
Even a thin layer of water could prevent the keys from being operated.
• Check that the ventilation openings are not blocked and do not place cookware in the direct vicinity of the induction
cooker.
• Place a pan with food or liquid in the centre of a cooking zone.
• Insert the plug in the socket and a beep will sound. The indicator lights of both cooking zones flash on the display. The induction
cooker is now in standby position. As long as the induction cooker is in standby position, the indicator lights continue to flash.
• Press the [ ON/STANDBY ] key to select the required cooking zone.
• Press the [ MENU ] key to activate the required cooking zone. The cooking zone is ready for heating. The indicator light for
power lights up and the power is shown on the display.
• Turn the control key to the left [ - ] or right [ + ] to set the required power.
• Press the [ MENU ] key to change from power display to temperature display and vice versa. The indicator light for temperature
lights up and the temperature is shown on the display.
• If there is no pan on the cooking zone after switching on, the induction cooker will not get hot. The error message [ E0 ] appears
on the display and an alarm signal sounds to indicate that no pan has been placed. One minute later, the induction cooker
switches off automatically.
Number of positions
Power range
Temperature range

SETTING THE TIMER

• Press the [ MENU ] key of the required cooking zone twice to set the timer. [ 0:00 ] flashes on the display. The indicator light
of the timer of the required cooking zone lights up. Turn the control key to the right [ + ] or left [ - ] to adjust the time. The timer
can be set from 1 minute to 3 hours.
• Once the time has been set, it will flash a number of times and then start to count down. The display will alternate between the
time and the temperature/power position.
• When the set time has passed, a beep sounds and the cooking zone switches off automatically. On the display you can see a
flashing [ OFF ] and the indicator light of the cooking zone flashes.
• The induction cooker switches off automatically after the maximum cooking time (3 hours) has passed, if you did not
set a time yourself.
SWITCHING OFF THE INDUCTION COOKER
• When the maximum cooking time or set time has passed, the induction cooker switches off automatically.
• Press the [ ON/STANDBY ] key to switch off the induction cooker manually.
Caution: the glass in the cooking zone area will be too hot to touch.
• After switch-off, the internal ventilation continues to run for approximately 1 more minute in order to cool the cooker.
• Remove the plug from the socket if you will not be using the cooker for a longer period of time.
16
• English
VKI3010ZWA-instructions.indd 16
Cooking zone - Ø 17 cm Cooking zone - Ø 14 cm
10 10
200 - 1600 watts 200 - 1300 watts
60 - 240°C 60 - 240°C
13-9-2018 09:25:04