Operating Controls; Operation; Technical Data; Care And Cleaning - Renkforce BM02 Bedienungsanleitung

Operating controls

1
10
9
1 Housing
2 Carrying handle (removable)
3 Screw
4 Battery compartment
5 Fan (not visible)

Operation

• Place the bubble machine on a horizontal, flat and stable surface.
• If battery operation is planned, insert 2x 1.5 V type C batteries (not included) into the battery
compartment (4). To do this, remove the screw (3) of the battery compartment lid using a
Phillips screwdriver and take off the lid.
• Pay attention to the polarity markings (+/-) shown in the battery compartment. Replace the lid
of the battery compartment and lock it with the screw.
Battery operation is possible for approx. 8 – 10 h depending on the condition
and quality of the batteries, as well as environmental conditions such as room
temperature.
• Make sure that the power adapter is not plugged in and the ON/OFF (7) switch is set to
"0" / "OFF".
• Fill the container (10) from the open front side by a maximum of 250 ml of the soap bubble
liquid.
• The rings of the bubble generator (9) must be immersed in the soap bubble liquid during
rotation.
• Remove the batteries if the product must be used with the power adapter.
• Plug the low-voltage plug of the power adapter into the DC 3 V socket (8).
• Plug the mains plug into a suitable mains socket.
• Set the ON/OFF switch to ON to switch on the bubble machine.
• Soap bubbles are produced at the bubble generator (9). Once the soap bubble liquid is used
up, switch off the device and disconnect it from the power supply to refill the soap bubble
liquid. Make sure that the device never operates continuously for more than 60 minutes. After
that, the device must rest for approx. 15 minutes.
• Set the ON/OFF switch to OFF to switch off the device after use. Disconnect the mains plug
of the power adapter from the mains socket.
Protect sensitive objects such as electronic devices that could be reached by the
soap bubbles.
The device may not be operated continuously for more than an hour.

Care and cleaning

• Disconnect the product from the mains supply and remove the batteries before each cleaning.
• To drain the soap bubble liquid, hold the removable carrying handle (2) and pour out the
contents from the front filling opening into a suitable sink (e.g. a kitchen sink).
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as
they can cause damage to the housing and malfunctioning.
• Clean the product with a dry, fiber-free cloth.
2 3 4 5
6 Intake grille (not visible)
7 ON/OFF switch (not visible)
8 Power adapter plug socket, DC 3 V (not visible)
9 Bubble generator
10 Bubble liquid container
Disposal
a) Product
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product according to
the relevant statutory regulations.
6 Remove any inserted batteries and dispose of them separately from the product.
b) Batteries
7
As the end user, you are required by law (Battery Ordinance) to return all used
8
batteries; they must not be disposed of in household waste!
Contaminated batteries are labelled with this symbol to indicate that disposal in
household waste is prohibited. The designations for the heavy metals involved are:
Cd = Cadmium, Hg = Mercury, Pb = Lead (the designation is on the batteries, e.g.
below the trash symbol on the left).
Used batteries can be returned free of charge to collection points in your municipality, our
stores or wherever batteries are sold.
You thus fulfil your statutory obligations and contribute to the protection of the environment.

Technical data

a) General
Input voltage/current ..................................3 V/DC, 800 mA
Power consumption ...................................2.4 W
Battery operation ....................................... 2 x 1.5 V type C batteries, LR 14
Soap capacity ............................................250 ml (soap bubble liquid is not supplied)
Soap consumption .....................................approx. 250 ml in 40 min. (approx. 375 ml/h)
Coverage area of the soap bubbles ..........approx. 1 x 1 m
Protection class .........................................III
Operating / storage conditions ...................0 to +40 ºC, 0 – 90 % RH
Dimensions (L x W x H) .............................225 x 180 x 150 mm
Weight (without power adapter) .................600 g
b) Power adapter
Input power/current of the power adapter ..100 – 240 V/AC, 50/60 Hz, 0.2 A max.
Output power/current .................................3 V/DC, 800 mA
Protection class .........................................II
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE.
(batteries are not supplied)
*02_1518779_V3_0317_02_hk_m_en