Operation; Troubleshooting - Sygonix 1462495 Bedienungsanleitung

Positioning
• Place the product on a flat and stable surface.
• The ventilation slot (5) must not be obstructed.
• Align the product in such a way, that the ventilation slot points to the middle of the room.

Operation

If you suffer from asthma or bronchial diseases, contact your physician before using
the product.
The product generates a small amount of ozone during use. Under normal
conditions, this does not affect the human body. If you or other persons are sensitive
to such ozone, immediately disconnect the product from the mains and open the
window.
Some electric discharge may occur during operation, causing slight crackling noise.
That is normal and not a fault.
There might also be slight odors occurring during operation, similar to the smell of
soil after rain. That is normal and not a fault.
• Make sure the product is turned off. The on/off switch (6) must not be countersunk in the
housing, but it must slightly protrude.
• Connect the low-voltage plug of the USB cable to the power connection (4).
• Connect the USB plug of the USB cable to the respective socket of the power adapter.
• Connect the power adapter to a common household wall socket.
You may also connect the product directly to an available USB port of a PC or to
a suitable vehicle USB adapter. In such a case, make sure the USB port provides
sufficient current.
• Press the on/off switch to turn on the product. The status LED (7) lights up and the product
starts generating anions immediately. The anions escape from the ventilation slot into the
room.
• Turn off the product after use, and disconnect the power adapter from the wall socket, if not
using the product for a longer period of time.
Filter replacement / fragrance chamber
• Make sure the product is turned off.
• Carefully remove the lid (1).
• Replace the activated carbon filter (3), once the filter – and hence the product – starts
producing an unpleasant smell. Remove the filter and replace it with a new filter of identical
type. Cut the new filter in such a way, that it features the exact same dimensions as the old
one.
• Fill the fragrance chamber (8) with a few drops of your preferred essential oil. There is a
small sponge inside the fragrance chamber for absorbing the oil. Even when the product is
not switched on, the fragrance starts spreading through the ventilation slot. Once you switch
on the product, that effect will be further enhanced.
• Reinstall the lid. Position the lid at an angle, thereby inserting the short lug into the rear
opening. Carefully press down the lid, until the long lug (2) locks into the front opening.

Troubleshooting

Problem
The status LED does not light up. The
product does not turn on.
The airflow reduces. The noise gets louder.
Cleaning and care
• This product does not require maintenance. There are no components inside the product
which need to be maintained by you. Have maintenance and repairs done by qualified
experts or repair shops only.
• Disconnect the product from the mains supply before cleaning.
• Under no circumstances use aggressive cleanings agents, cleaning alcohol or other chemical
solutions since these can penetrate the housing or impair functionality.
• Never submerge the product in water or other liquids.
• Clean the product with a dry, fibre-free cloth. Do not apply too much pressure to the housing
to prevent scratching.
• Use a dry brush in order to regularly remove dust from the ventilation slot.
• Let fresh air run through the ventilation slot in regular intervals.
Solution
Check the cable for correct connection.
Replace the filter. Clean the ventilation slot.
Disposal
Electronic devices are recyclable waste and must not be disposed of in the
household waste. At the end of its service life, dispose of the product in accordance
with applicable regulatory guidelines.
You thus fulfill your statutory obligations and contribute to the protection of the
environment.
Technical data
a) Air cleaner
Operating voltage ......................... 5 V/DC via USB
Power consumption ...................... 2 W
Suitable room size ........................ max. 10 m
Anions ........................................... >1 million/m
Housing material ........................... ABS
Operating conditions ..................... 0 to +45 °C, 20 - 80 % RH
Storage conditions ........................ -10 to +60 °C, 20 - 85 % RH
Dimensions (W x H x D) ............... 144 x 60 x 130 mm
Weight .......................................... 220 g
b) Power adapter
Input voltage ................................. 100 – 240 V/AC, 50/60 Hz
Output voltage .............................. 5 V/DC
Output current ............................... 0.5 A
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2016 by Conrad Electronic SE.
2
3
*1462495_V1_0916_02_IPL_m_en