Inhaltsverzeichnis
Werbung
Compliance Information
FCC Compliance Information
This device complies with FCC Rules Part 15. Operation is subject to the following two conditions:
This device may not cause harmful interference, and this device must accept any interference received, including interference that may cause
undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with manufacturer's instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Increase the separation between the equipment and signal source. Connect the equipment to an outlet on a circuit different from that to which the
signal source is connected.
Consult the dealer or an experienced computer technician for help. The use of shielded cables for connection of the monitor to the graphics card is
required to ensure compliance with FCC regulations. Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
CE Compliance Information
EMC Directive 89/336/EEC and Amendment 92/31/EEC, Class B Digital Device EN 50081-14, Generic Emissions Standard for Residential,
Commercial and Light Industrial Products (EN 55022/CISPR 22, Limits and Methods of measurement of Radio). (EN 55022/CISPR 22, Limits and
Method of Measurement of Radio Interference Characteristics Information Technology Equipment) Warning: This is a Class B product. In a domestic
environment this product may cause radio interference in which case the user may be required to take adequate measure. EN 50082-1, Generic
Immunity Standard for Residential, Commercial and Light Industrial Products (IEC 801-2, IEC 801-3, IEC 801-4)
Macrovision Corporation
This device is protected by U.S. Patent numbers 4.631.603: 4,577,216; and 4,819,098 and other intellectual property rights. The use of Macrovision's
Copy Protection technology in the device must be authorized by Macrovision and is intended for home and other limited pay-per-view uses only, unless
otherwise authorized in writing by Macrovision. Reverse engineering or disassembly is prohibited.
Legal Information
Software License Agreement
Single User Products
The EVGA ADM software (the "Software") is copyrighted by EVGA.com Corp. and is is protected by U.S. Patent Number 6, 832, 312. All rights are
reserved. The purchaser is granted a license to use the Software only, subject to the following restrictions and limitations:
1. The license is for the original purchaser only, and is not transferable without written consent from EVGA.
2. The original purchaser may use the Software on a single computer owned or leased by the original purchaser. You may not use the Software on
more than a single machine, even if you own or lease more than one machine, without written consent from EVGA.
3. The original purchaser may make backup copies of the Software for his or her own use only, subject to the use limitations of this license.
4. The original purchaser may not engage in, nor permit third parties to engage in, any of the following:
•
Providing or disclosing the Software to third parties.
•
Providing use of the Software in a computer service business, network, time –sharing, multiple CPU or multi-user arrangement to users who
are not individually licensed by EVGA
•
Making alterations or copies of any kind in the Software (except as specifically permitted above).
•
Attempting to unassemble, de-compile or reverse engineer the Software in any way.
•
Granting sublicenses, leases, or rights in the Software to others.
•
Making copies, or verbal or media translations, of the user's guide.
•
Making telecommunication data transmissions of the Software.
Trademark Information
2001-2005 EVGA.com Corp. EVGA, the EVGA logo and combinations thereof are trademarks of EVGA.com Corp. All brands and companies are
trademarks of registered Trademarks of their respective companies. EVGA reserves the right to terminate this license if there is a violation of its terms
or default by the Original Purchaser. Upon termination, for any reason, all copies of the Software must be immediately returned to EVGA and the
Original Purchaser shall be liable to EVGA.com Corp. for any and all damages suffered as a result of the violation or default.
15
Werbung
Inhaltsverzeichnis
