Usb Charging Function - Conrad 76 96 50 Bedienungsanleitung

Note:
The „BAT" Status LED. (7) glows red when the power transformer is con-
nected and the 9V battery is inserted. The „BAT" Status LED. (7) flashes once
a second when the battery voltage is low. The „BAT" Status LED. (7) flashes
twice per second when the battery needs changing.
• Place the mobile phone ring tone amplifier on a flat, vibration-free, dry and level surface.
• Insert your mobile phone. A short „beep" tone sounds, for audible confirmation that your mobile
phone has been detected. The „Call/SMS detection LED" (4) flashes once, for visual confirma-
tion that your mobile phone has been detected.
• Push the two „securing clips" (10) together, to ensure the mobile phone is held in place
securely.
• Set the volume and the desired ring tone for the mobile phone ring tone amplifier by using the
slide switch „OFF/LO/HI" (1) and „RING/MUSIC" (2).
Handling in the event of incoming calls and text messages (SMS)
In the event of an incoming call or text messages (SMS), the mobile phone ring tone amplifier
emits (after a delay of up to 5 seconds), an signal tone via the „acoustic signaller" (5). The
„CALL/SMS detection LED" (4) flashes while the signal is sounded. Then, remove the mobile
phone. The signal tone stops and the „Call/SMS detection LED" (4) stops blinking.
Indication of a missed call or a received SMS
If a call or a SMS has been received and the mobile phone was not taken from the mobile phone
ring tone amplifier, this is indicated by the „Call/SMS detection LED" (4) flashing at intervals of
20 seconds.

USB charging function

A USB recharger cable for mobile phones can be connected via the „USB charging connection"
(9) thus ensuring your mobile phone's battery is charged (charging cable not included).
Please consult the operating manual for your mobile phone, before using the
mobile phone ring tone amplifier's charging function.
You can obtain information about appropriate accessories for charging your
mobile phone via USB from specialist shops.
The green Status LED „CH". (8) flashes twice per second, while your mobile phone battery is
charging.
When the battery of your mobile phone is fully charged, the green „CH." status LED (8) glows
steady.
If the charging current exceeds 500mA, the charging function is stopped and
the green „CH." status LED (8) flashes 4 times per second. This is a protec-
tive measure to protect your mobile phone against damage.
Replacing the Battery
If the „BAT." Status LED (7) flashes 2x per second, the 9V battery needs changing. To do this,
proceed as follows:
• Open the battery compartment on the back.
• Remove the used 9V battery.
• Connect the 9V battery, observing the correct polarity and insert it into the battery compart-
ment.
• Close the battery compartment.
Maintenance and Cleaning
Except for replacing the battery as described, the device is maintenance-free.
To clean the outside of the product, a dry, soft and clean cloth is sufficient. Do not use any
aggressive cleaning agents.
Disposal
a) In general
Please dispose of the device when it is no longer of use, according to the current
statutory requirements.
b) Batteries and rechargeable batteries
As a consumer you are required (Battery Ordinance) to responsibly dispose of all used batter-
ies and rechargeable batteries;it is forbidden to throw them away with the normal house-
hold waste!
Contaminated batteries/rechargeable batteries are labelled with these symbols to
indicate that disposal in the domestic waste is forbidden. The designations for the
heavy metals involved are: Cd = Cadmium, Hg = Mercury, Pb = Lead.
Used batteries, rechargeable batteries as well as coin cells can be returned to col-
lection points in your municipality, our stores or wherever batteries/rechargeable
batteries/coin cells are sold!
You thus fulfil the legal requirements and make your contribution to protecting the environment!
Technical Data
Operating voltage:
Sound pressure:
Operating temperature:
Weight:
Dimensions (W x H x D):
Declaration of Conformity (DOC)
We, Conrad Electronic, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that this
product conforms to the fundamental requirements and the other relevant regulations of the
directive 1999/5/EG.
You can find the Declaration of Conformity for this product at
www.conrad.com.
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or
the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2009 by Conrad Electronic SE.
9V/DC via the enclose power transformer
up to 105 dB(A)
0° to 40°C
32 grams (excl. battery)
38 x 74 x 28 mm