Intended Use; Package Contents; Safety Instructions - Conrad Flamelight Bedienungsanleitung

G
O P E R A T I N G I N S T R U C T I O N S
Torch "Flamelight"
Item no. 1216214

Intended use

The product is intended to generate an optical effect for decorative purposes; it may be in-
stalled and used only in dry, enclosed indoor rooms.
Two built-in strong radial fans blow a thin, half-transparent silk cloth upward, where it is illumi-
nated by LEDs. This construction simulates the fire/light of a torch.
Always observe the safety instructions and all other information included in these operating
instructions. Read the operating manual carefully; keep it in a safe place or pass it on to others
using the product.
Any use other than that described above could lead to damage to this product and involves the
risk of short circuits, fire, electric shock, etc.
This product complies with the applicable national and European requirements. All names of
companies and products are the trademarks of the respective owners. All rights reserved.

Package contents

• Torch with cloth insert
• Power cable
• Operating instructions
Explanation of Symbols, Inscriptions
The lightning symbol inside a triangle is a warning to inform you of potential risks of
personal injury, such as electrical shock.
This symbol indicates specific risks associated with handling, function and use.
The "hand" symbol represents special tips and operating information.
The product is only intended to be installed and used in dry, indoor spaces; it must
not get damp or wet.
Observe the operating instructions!

Safety Instructions

The warranty/guarantee will be void in the event of damage caused by failure
to observe these operating instructions! We do not assume any liability for
any resulting damage!
We do not assume any liability for material and personal damage caused by
improper use or non-compliance with the safety instructions! In such cases,
the warranty will be null and void.
a) General
• The unauthorised conversion and/or modification of the product is not permitted
for safety and approval reasons (CE). Do not open/disassemble! Contains no
customer-serviceable parts.
Maintenance, adjustment or repair work may only be carried out by an expert/au-
thorised service centre, which is familiar with the hazards involved and the relevant
regulations.
• This product is not a toy. Devices operated using mains voltages should not be
used by children. Therefore, be especially careful when children are around.
• The product is designed according to Protection Class I. It may only be used when
connected to an earthed mains socket.
• Do not carelessly leave the packaging material lying around since this may be-
come a dangerous toy for children.
• Handle the product with care; it may be damaged by impacts, blows, or accidental
falls, even from a low height.
• If you have any questions that are not answered in these operating instructions,
please contact our technical department or another specialist.
www.conrad.com
Version 09/14
b) Installation location
• The product may be used in dry, enclosed indoor areas only; it must not get damp
or wet! Never set up the product in the direct vicinity of a bathroom, shower, bath-
tub or similar. There is danger to life through an electric shock!
• The product must be set up on a horizontal, stable, level, sufficiently large surface.
Never set the product on carpets.
Protect valuable surfaces by using a suitable mat to prevent scratches or pressure
points.
• Air turbulence arises near the installation location due to the air blown out upward
from the torch and also the air being pulled in. For this reason, keep a sufficient
distance from open flame (e.g. candles, fireplaces, etc.). There is a risk of fire!
• Keep away from small or lightweight objects. These could be sucked into the
product, which can damage the product. There is also a danger of fire in certain
circumstances!
• The product must not be installed and used in vehicles.
• Keep the product out of the reach of children. Position the product so it is out of the
reach of children.
Children could attempt to poke objects into the product. Not only does this damage
the product, but it also poses an injury hazard as well as a risk of fatal electrical
shock!
• The product must not be exposed to extreme temperature, direct sunlight or strong
vibrations. Protect the product from dust and dirt.
• Do not operate the device in environments where there are high levels of dust,
flammable gases, vapours or solvents. There is a danger of fire and explosion!
• The power cable must not be pinched or damaged by contact with sharp edges.
Do not place any objects on the cable, and do not allow it to become kinked. Install
the cable where no one can stumble over it and the plug is easily accessible. Do
not install the mains cable under carpets or the like.
• The mains outlet used for the connection must be located close to the product and
easily accessible.
c) Handling and Use
• Never touch, operate, plug in or unplug the product with damp or wet hands. There
is danger to life through an electric shock!
• Never block the air intake or outlet openings.
• Never connect the product to the power supply immediately after it has been trans-
ferred from a cold room into a warm one (e.g., during transport). The condensation
that develops in such cases could damage the device or cause an electric shock!
Allow the product to reach room temperature. Wait until the condensation has
evaporated. This might take several hours. Only after this should it be plugged in
to the mains supply and put into use.
• Always pull a mains plug on the gripping surface intended for this purpose. Never
unplug the mains plug from a mains socket by pulling the cable!
• Do not use the product when it is damaged (e.g., housing, mains cable, mains
switch). There is danger to life through an electric shock!
Safe operation can no longer be assumed if:
- the product shows visible signs of damage
- the product does not work at all or works poorly (leaking smoke or a smell of
burning, audible cracking noises, discolouration to the product or the adjacent
surfaces)
- the product was stored under unfavourable conditions
- it was exposed to heavy loads during transport
If the product or power cord is damaged, do not touch it; there is a risk of fatal
electric shock!
First, turn off the mains voltage to all poles of the mains socket to which the prod-
uct is connected (e.g. switch off at the corresponding circuit breaker or remove the
safety fuse, then turn off at the ELCB).
Then you can remove the mains plug from the mains socket. Discontinue use of
the product, take it to a specialised workshop or dispose of in an environmentally
friendly manner.
• Use the product only in a temperate climate, never in a tropical climate.
• Switch the product off and unplug it from the mains socket before cleaning it or
when it is not to be used for a while.