Installation - VOLTCRAFT CO-500 Bedienungsanleitung

O P E R A T I N G I N S T R U C T I O N S
AMBIENT AIR INDICATOR CO-500
Item no. 10 13 01
INTENDED USE
The ambient air indicator "CO-500" is a stationary measuring device for determining the concentration of
carbon dioxide (CO ) in the ambient air with NDIR measuring methods (non-dispersive infrared absorption
2
measurement) that are more exact and more stable over time.
The meter is intended for monitoring the carbon dioxide level in the room air in order to take appropriate
early measures for ventilation. An increased CO
effi ciency and performance.
The quality level is displayed by means of a traffi c light indicator (green/yellow/red). The air temperature
and humidity are measured at the same time. All three values are indicated on the display at the same
time.
The device operates on a power supply (included).
Any use other than that described above could lead to damage to this product and involves the risk of short
circuits, fi re, electric shock, etc. The safety instructions and all other information must be followed at all
times!
This product complies with the applicable national and European regulations.
All names of companies and products are the trademarks of the respective owner. All rights reserved.
PACKAGE CONTENTS
• Ambient air indicator
• Power adaptor
• Power cable
• Operating Instructions
EXPLANATION OF SYMBOLS
The lightning symbol indicates a health hazard, e.g. electric shock.
The exclamation mark indicates specifi c risks associated with handling, function and use.
The "arrow" symbol indicates special tips and operating information.
SAFETY INSTRUCTIONS
The warranty will be void in the event of damage caused by failure to observe these
safety instructions! We do not assume any liability for any consequential damage!
We shall not accept liability for damage to property or personal injury caused by incor-
rect handling or non-compliance with the safety instructions. In such cases, the warranty
will be null and void.
• The unauthorised conversion and/or modifi cation of the unit is not permitted for safety and
approval reasons (CE).
• The product is not a toy and should be kept out of the reach of children!
• The product may be used only in dry, closed interiors; it must not get damp or wet! Otherwise,
there is a risk of a life-threatening electric shock!
• Operate the ambient air indicator using the enclosed mains adapter only. Do not use any
other power supply.
• Never touch the mains adapter or the power cable with wet or damp hands. There is a risk of
a lethal electric shock!
• Do not pull the mains plug from the socket by pulling on the cable.
• Protect all cables of the mains adapter from sharp corners; do not kink them.
• Protect the product from extreme temperatures, direct sunlight and strong shocks/vibrations.
Do not install the ambient air indicator in rooms with high dust exposure.
• Do not use this product in rooms or under adverse ambient conditions where combustible
gases, vapours or dust are or may be present! There is a risk of explosion!
• The mains adapter complies with the protection class II.
• Do not leave packaging material lying around carelessly. They could become a dangerous
plaything for children.
• Handle the product with care. The product can be damaged if crushed, struck or dropped,
even from a low height.
Version 12/11
level leads to fatigue, lack of concentration and loss of
2
• If you have reason to assume that safe operation is no longer possible, disconnect the prod-
uct immediately and secure it against accidental operation. A safe operation can no longer be
assumed, if:
- the product shows visible signs of damage,
®
- the product ceases to function
- the product was stored for a longer period of time in unfavourable conditions
- it was exposed to heavy loads during transport.
• In commercial institutions, the accident prevention regulations of the Employer's Liability
Insurance Association for Electrical Systems and Operating Materials are to be observed.
• Carbon dioxide (CO
2
during all measurements. To protect the life of humans and animals, this device must not be
used in areas where high concentrations of carbon dioxide are used industrially.
If in doubt about how to connect the device correctly, or should any questions arise that are not answered
in these operating instructions, please contact us or another specialist.
VOLTCRAFT®, Lindenweg 15, D-92242 Hirschau, Tel. 0180/586 582 7.
DESCRIPTION OF THE PARTS
1
2
7
3
4
8
5
6
1 Hanging eyes for wall mounting
2 Rubber covering (if there is a DIP switch it is behind this, and this is used for the manufacturer's
programming – do not adjust!)
3 Opening for air measurement
4 SubD jack for programming by the manufacturer
5 On/Off switch
6 Low-voltage socket for connecting the power supply
7 Display of the CO concentration in ppm
2
8 Sensor for automatic brightness adjustment
9 Air quality indicator in traffi c colours (green/yellow/red)
10 Display of the room temperature in °C (degrees Celsius)
11 Room humidity display

INSTALLATION

Place the ambient air indicator so that suffi cient ambient air can fl ow through it. The air fl ow for measure-
ment enters the device at the back. Avoid narrow spaces, such as between books, etc., in order to prevent
any effects on the measured results. Choose a place where a mains socket is available close by.
With the hanging eyes (1) on the back, the device can easily be hung on two screws, nails, or wall hooks
(distance between eyes: 160 mm). Hanging on two thin steel cables is also conceivable.
Because of the heavy weight, make sure the mounting is stable!
) is a transparent and odourless gas. Pay attention to your own safety
9 10 11