Renkforce 1620609 Bedienungsanleitung Seite 3

Operating instructions
USB charger with 4 ports
Item no. 1620609
USB charger with 4 ports
Item no. 1665144
Intended use
This product provides four USB power outputs for charging USB devices (e.g. smartphones
or tablets). Power is provided via the mains adapter (see "Technical data" section). The ports
can be switched on and off individually. The product cannot be used to transfer data between
USB devices. This product is intended for indoor use only. Do not use it outdoors. Contact with
moisture (e.g. in bathrooms) must be avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. Using
the product for purposes other than those described above may damage the components. In
addition, improper use can cause hazards such as a short circuit, fire or electric shock. Read
the instructions carefully and store them in a safe place. Only make this product available to
third parties together with its operating instructions.
This product complies with statutory national and European regulations. All company and
product names are trademarks of their respective owners. All rights reserved.
Package contents
• USB charger
• Adapter
• Operating instructions
Latest operating instructions
To download the latest operating instructions, visit www.conrad.com/downloads or scan the QR
code on this page. Follow the instructions on the website.
Explanation of symbols
The symbol with the lightning in a triangle indicates that there is a risk to your health,
e.g. due to an electric shock.
The symbol with an exclamation mark in a triangle is used to highlight important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on how to use the
product.
This symbol indicates that this product is built according to protection class II. It is
equipped with reinforced or dual insulation between the mains circuit and the output
voltage.
The product must only be installed and used in dry, indoor locations. It must not
become damp or wet, as this may cause a fatal electric shock!
Safety instructions
Read the operating instructions and safety information carefully. If you do
not follow the safety information and information on proper handling in these
operating instructions, we will assume no liability for any resulting personal
injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) General information
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly, as it may become a
dangerous toy for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, stop using it and prevent
unauthorised use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stress.
• Always handle the product carefully. Jolts, impacts or a fall even from a low height
may damage the product.
• Always observe the safety and operating instructions of any other devices which
are connected to the product.
• Consult a technician if you are not sure how to use or connect the product.
• Maintenance, modifications and repairs must be done by a technician or a
specialist repair centre.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
b) Electrical safety
• Before connecting the product to the mains, check that your local A/C mains
voltage matches the specifications on the nameplate.
• This device was constructed according to protection class II. Only connect the
adapter plug to a standard mains socket (230 V/AC, 50 Hz) connected to the
public grid.
• Never pour liquids over electrical devices or place objects filled with liquid next
to the product. If liquid or an object does enter the interior of the device, power
down the respective socket (e.g. switch off the circuit breaker), and then remove
the mains plug from the mains socket. Discontinue use and take the product to a
specialist repair centre.
• Never use the product immediately after it has been brought from a cold room
into a warm one. The condensation generated may destroy the product, and the
mains adapter may cause a fatal electric shock! Allow the product to reach room
temperature before connecting it and putting it to use. This may take several
hours.
• Do not touch the adapter if there are any signs of damage, as this may cause
a fatal electric shock! Switch off the mains voltage to the socket containing the
mains adapter (switch off at the corresponding circuit breaker or remove the
safety fuse, and then switch off at the corresponding RCD protective switch). You
can then unplug the mains adapter from the mains socket. Discontinue use and
dispose of the adapter in an environmentally friendly manner. Replace it with an
adapter with the same specifications.
• The mains outlet must be located near to the device and be easily accessible.
• Never connect or disconnect power adapters if your hands are wet.
• Never unplug the power adapter from the mains socket by pulling on the cable.
Always use the grips on the plug.
• When setting up the product, make sure that the cables are not pinched, kinked
or damaged by sharp edges.
• Always lay the cables so that nobody can trip over or become entangled in them.
This may cause an injury.
• For safety reasons, disconnect the adapter from the mains socket during
thunderstorms.
• Never leave the product unattended during use.
• The housing warms up during use. Ensure that there is sufficient ventilation. Do
not cover the housing!
Product overview
Item no. 1620609
3
4
5
2
1
2
1
2
1
2
Item no. 1665144
3
4
2
1
2
1
2
1
2
Setup and installation
• Remove all connected USB devices and unplug the adapter from the power-in socket (3) on
the USB charger.
• You can place the USB charger on a heat-resistant surface or attach it to a wall, overhead
objects or under a table or other piece of furniture using the mounting straps (7).
• Use the USB charger as a template and mark the centre of the screw holes (7).
• Drill the required holes in the surface.
Ensure that no existing cables or pipes (including water pipes) are damaged
when drilling mounting holes or tightening screws.
• Use suitable screws (e.g. chipboard screws), or in the case of mineral surfaces such as brick
or plasterboard walls, suitable dowels (not included).
• After mounting the USB charger in place, connect the USB devices to the charger and
connect the adapter to the power-in socket (3).
1 Function LEDs
2 USB port
3 Power-in socket (not shown)
6
4 Power LED
5 On/off switch (only for item no.
7
1620609)
1
6 Ventilation openings
7 Mounting straps
6
7
1