Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Halogen Heater
Item no. 56 01 21
1.
Intended use
This halogen heater is suitable for heating in places such as offices and living areas. By simply
pressing a button, the halogen heater will automatically turn to the left and and to the right for an
optimal heating effect. The halogen heater requires a power supply of 230 V/AC, 50 Hz. You may
therefore only use a 230 V/AC power outlet of the public supply grid. Never try to operate the
halogen heater with another voltage. Use is only permitted in closed, dry rooms, i.e. not outdoors
or in the bathroom. Select a place to set up the halogen heater where it will be protected from
moisture, heavy soiling or overheating.
Unauthorised conversion and/or modification of the device are inadmissible because of safety
and approval reasons (CE). Any usage other than described above is not permitted and can
damage the product and lead to associated risks such as short-circuit, fire, electric shock, etc.
Please read the operating instructions thoroughly and keep them for further reference.
2.
Delivery content
•
Halogen heater
•
Stand
•
2 x screws
•
Operating instructions
3.
Safety instructions
We do not assume liability for resulting damages to property or personal injury
if the product has been abused in any way or damaged by improper use or
failure to observe these operating instructions. The warranty/ guarantee will
then expire.
The icon with exclamation mark indicates important information in the
operating instructions. Carefully read the whole operating instructions before
operating the device, otherwise there is risk of danger.
Personal safety
•
The halogen heater should be kept out of the reach of children. Be particularly careful when
children are present, especially when they try to push objects through openings in the housing
and into the device. There is risk of a fatal electric shock. When using the heater, keep a good
eye on children and animals present so that they do not burn themselves on the heater or start
a fire by knocking the heater over or covering it up.
•
Do not use the heater near other sources of heat. Position the heater so that flammable objects
will not be set alight (e.g. curtains). Therefore make sure the heater is in a safe position. The
air inlets and outlets on the heater must be unobstructed. The heater must not be covered up,
e.g. with cloths. There is risk of fire. The halogen heater must be at least 50 cm away from
walls or other objects when in operation.
•
Never touch the housing or the air outlet grill when the heater is in operation or has not yet
cooled down (risk of burns).
•
Do not insert any objects into the air outlets or into the interior of the heater (risk of an electric
shock).
•
On commercial premises, the relevant accident prevention regulations of the relevant
professional insurance association for electrical systems and operating materials are to be
observed.
•
Never pour out liquids above the device. There is risk of a fatal electric shock. Should this
happen, pull the mains plug out of the socket immediately and contact an expert.
Product safety
•
The product must not be subjected to heavy mechanical stress.
•
The product must not be exposed it to extreme temperatures, direct sunlight, intense vibration,
or dampness.
•
Before using the device, check that the mains voltage that you want to operate the device with
matches the voltage specified on its nameplate.
•
Check both the halogen heater as well as the connection cable for damage from time to
time.
•
Place the power supply cable such that it does not come into contact with hot parts of
theheater.
•
Do not use a double adapter or a similar device to connect the heater to the mains.
•
Never switch the halogen heater on immediately after having taken it from a cold to a warm
environment. The condensation water that develops may destroy the heater. Allow the heater
reach room temperature before turning it on.
•
Never pull on the connection cable to move the device. Make sure that the connection cable
does not get caught somewhere unintentionally, leading to a danger of the heater falling over.
Do not wind the connection cable around the heater. Do not kink the connection cable.
•
Do not use the halogen heater in rooms or under adverse ambient conditions where there are
or could be combustible gases, vapours or dust.
•
If you have reason to believe that safe operation is no longer possible, take the halogen heater
out of operation immediately and secure it against inadvertent operation. It must be assumed
that safe operation will no longer be possible if
-
There is visible damage to the halogen heater
-
The halogen heater no longer functions
-
The heater has been stored for a long period of time under unfavourable conditions
-
The heater may have been subjected to considerable stress during transportation.
Miscellaneous
Version 09/09
•
Servicing, adjustment or repair works must only be carried out by a specialist/ specialist
workshop.
•
Live components may be exposed if the cover is opened or if components are removed.
Terminals may also be live. Before maintenance, repair work or replacing components or
assemblies, the halogen heater must be disconnected from the mains power. Maintenance
and repair on the halogen heater must only be carried out by a SPECIALIST who is familiar
with the hazards involved and with the relevant regulations.
•
If any questions arise that are not answered in this operating instruction, contact our Technical
Advisory Service or other experts.
4.
Assembly
Before assembling the halogen heater, disconnect the mains plug from the
mains power.
1.
The stand must firstly be mounted on the housing of the halogen heater. Use the following
diagram to help you when assembling the heater.
2.
The stand can best be mounted when the heater is lying on its back.
3.
Remove the two screws from underneath the heater, pull the connection cable through the
middle of the stand and attach the stand.
4.
Secure the stand on the heater by tightening the two screws.
1
Housing
2
Stand
3
Fastening screws (2 pieces)
4
Safety device
5
Cable compartment
6
Power supply cable
5.
Operation
Always place the halogen heater on a firm, flat and stable surface.
Never operate the halogen heater without the honeycombed grill.
If the halogen heater is not to be used for a long period of time, store it in a
clean and dry place.
The heater must not be used near bathtubs, showers, swimming pools or
washbasins. It must not be possible to operate the heater when you are in
contact with water.
7
Main switch and first heating power level (400 W)
8
Switch for second heating power level (400 W)
9
Switch for third heating power level (400 W)
10
Switch for oscillation mode
11
Rod-shaped halogen bulb
12
Honeycombed grill
1.
Now insert the mains plug into a mains socket for the public supply grid.
2.
You switch the halogen heater on by pressing the main switch „7" (POWER). The first heating
level (400 W) is activated.
3.
You switch the halogen heater off by pressing the main switch again. Always pull out the
mains plug from the mains socket after you switch the halogen heater off.
4.
By pressing buttons „8" and „9" (400 W), you can increase or decrease the heating power.
(W is watts)
5.
If you press the oscillation switch „10" (TURN), the heater will start to turn to the left and to
the right.
6.
The halogen heater is equipped with a safety device that switches the heater off automatically
if it falls over.
7.
If the heater does not work when you switch it on, check to see whether it is standing on a firm,
flat and stable surface and whether the switch of the safety device is jammed.
6.
Cleaning and maintenance
Observe the safety instruction for this and pull the mains plug out of the
socket.
Before cleaning the heater, always pull out the mains plug and allow the heater to cool down. The
housing can be wiped clean with a slightly moist cloth. Do not use abrasives. This could damage
the coating. If the openings are dirty, they can be cleaned with a vacuum cleaner. If you are not
using the heater, keep it stored in a safe and dry place.
7.
Disposal
In order to preserve, protect and improve the quality of environment, protect human
health and utilise natural resources prudently and rationally, the user should return
unserviceable product to relevant facilities in accordance with statutory regulations.
The crossed-out wheeled bin indicates the product needs to be disposed separately
and not as municipal waste.
8.
Technical data
Operating voltage:
230 V/AC, 50 Hz
Power output:
400/800/1200 W
Switch settings:
3
Cable length:
1.5 m (fixed)
Dimensions (W x H x D):
345 x 550 x 125 mm (heater)
400 x 40 x 290 mm (stand)
Weight:
approx. 3.5 kg
9.
Declaration of conformity
We, Conrad Electronic, Klaus-Conrad-Strasse 2, 92240 Hirschau, Germany, hereby declare that this
product complies with the fundamental requirements and the other relevant provisions of Directive
1999/5/EC. You can find the conformity declaration for this product under www.conrad.com.
These operating instructions are a publication by Conrad Electronic SE,
Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming,
or the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© 2009 by Conrad Electronic SE.
*02_09/09_01-SB
Werbung
