Attachment Of The Crossover; Connecting The Crossover - Rainbow audio IL-C6.2F Einbauanleitung

Connection of Amplifier/Radio:
Attach prepared loudspeaker cable (2.5 mm²) at the screw connections „Input" of the crossover, whereby Attach prepared loudspeaker cable (2.5 mm²) at the screw connections „Input" of the crossover, whereby Attach prepared loudspeaker cable (2.5 mm²) at the screw connections „Input" of the crossover, whereby
the connector with the red conduit cover is connected with the positive terminal and the connector with the connector with the red conduit cover is connected with the positive terminal and the connector with the connector with the red conduit cover is connected with the positive terminal and the connector with
the black conduit cover with the minus connection. Attach the other end of the loudspeaker cable making
sure the polarity corresponds with that on the amplifier and radio sides. sure the polarity corresponds with that on the amplifier and radio sides.
Connection of Woofer:
Attach prepared loudspeaker cable (2.5 mm²) at the screw connections „Woofer" of the crossover, Attach prepared loudspeaker cable (2.5 mm²) at the screw connections „Woofer" of the cr Attach prepared loudspeaker cable (2.5 mm²) at the screw connections „Woofer" of the cr
whereby the connector with the red conduit cover is connected with the positive terminal and the whereby the connector with the red conduit cover is connected with the positive terminal and the whereby the connector with the red conduit cover is connected with the positive terminal and the
connector with the black conduit cover with the minus connection. Attach the other end of the connector with the black conduit cover with the minus connection. Attach the other end of the connector with the black conduit cover with the minus connection. Attach the other end of the
loudspeaker cable, making sure the polarity (+/-) of the connections corresponds, and connect to the loudspeaker cable, making sure the polarity (+/
woofers.
Connection of Tweeter:
Attach prepared loudspeaker cable (1 mm²) at the screw connections „Tweeter " of the crossover, Attach prepared loudspeaker cable (1 mm²) at the screw connections „Tweeter " of the crossover, Attach prepared loudspeaker cable (1 mm²) at the screw connections „Tweeter " of the crossover,
whereby the connector with the red conduit cover is connected with the positive terminal and the whereby the connector with the red conduit cover is connected with the positive te whereby the connector with the red conduit cover is connected with the positive te
connector with the black conduit cover with the minus connection. Connect the other end of the connector with the black conduit cover with the minus connection. Connect the other end of the connector with the black conduit cover with the minus connection. Connect the other end of the
loudspeaker cable, preferably with suitable contacts and making sure the polarity of the connections loudspeaker cable, preferably with suitable contacts and making sure the polarity of the connections loudspeaker cable, preferably with suitable contacts and making sure the polarity of the connections
correspond, to the available connection cable of the tweeters (+ = red marking) correspond, to the available connection cable
With all component systems, the tweeter range has been provided with a thermal protection device in the With all component systems, the tweeter range has been provided with a thermal protection device in the With all component systems, the tweeter range has been provided with a thermal protection device in the
crossover. This added measure protects the high-quality tweeter against overly high performance levels. crossover. This added measure protects the high
However, with extremely high performance levels, the thermal protection device will shut down the h extremely high performance levels, the thermal protection device will shut down the h extremely high performance levels, the thermal protection device will shut down the
tweeter to a low level. Once reduced the power to a normal level the thermal protection device will cool tweeter to a low level. Once reduced the power to a normal level the thermal protection device will cool tweeter to a low level. Once reduced the power to a normal level the thermal protection device will cool
down and will release tweeter from protection status after a few minutes. down and will release tweeter from protection status after a few
The component systems allow for the possibility to correct at the crossover the intensity of the acoustic The component systems allow for the possibility to correct at the crossover the intensity of the acoustic The component systems allow for the possibility to correct at the crossover the intensity of the acoustic
pressure in the tweeter range, in order to project a vivid and unobtrusive sound, depending upon location pressure in the tweeter range, in order to project a vivid and unobtrusive sound, depending upon location pressure in the tweeter range, in order to project a vivid and unobtrusive sound, depending upon location
of the tweeters by setting the cable jumpers. Therefore remove the cover of the crossover as described
in chapter "Attachment of the crossover". in chapter "Attachment of the crossover".

Attachment of the Crossover

Attachment of the Crossover
Fasten crossovers to a suitable, easily accessible, and well Fasten crossovers to a
location in the vehicle with the accompanying self-tapping screws 3,9x13 location in the vehicle with the accompanying self location in the vehicle with the accompanying self
(E) or double ) or double-sided tape. Therefore lift the cover of the crossover by
sidewise force. The bottom part of the crossover can now be us sidewise force. The bottom part of the crossover can now be used as a sidewise force. The bottom part of the crossover can now be us
mounting jig. Drill the mounting holes and fasten crossover. Put cover on mounting jig. Drill the mounting holes and fasten crossover. Put cover on mounting jig. Drill the mounting holes and fasten crossover. Put cover on
the crossover and press firmly until it snaps in. the crossover and press firmly until it snaps in.
Note: Do not attach crossovers with sink screws! When using sink screws
the mounting feet can be destroyed. During the plac the mounting feet
crossovers maintain a large distance from cable harnesses, in order to crossovers maintain a large distance from cable crossovers maintain a large distance from cable
avoid inductive distortion. If inductive distortion occurs, immediately change avoid inductive distortion
the position of the position of
Connecting the Crossover to headunit or amplifier Connecting the Crossover to headunit or amplifier Connecting the Crossover to headunit or amplifier
minus connection. Attach the other end of the loudspeaker cable making minus connection. Attach the other end of the loudspeaker cable making
le jumpers. Therefore remove the cover of the crossover as described le jumpers. Therefore remove the cover of the crossover as described
suitable, easily accessible, and well-ventilated
sided tape. Therefore lift the cover of the crossover by
attach crossovers with sink screws! When using sink screws
can be destroyed. During the placement of the
If inductive distortion occurs, immediately change
connections corresponds, and connect to the
quality tweeter against overly high performance levels.
24