Renkforce SM-305AG Bedienungsanleitung Seite 3

Operating instructions
SM-305AG Wireless mouse
Item no. 1217364 - grey
Item no. 1308851 - black
Intended use
The wireless computer mouse is used to operate a computer. The control commands
are transferred using a radio signal (wireless). FSK Auto-Link technology establishes
the connection between the mouse and computer fully automatically. The mouse is
particularly suited for use with notebooks.
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in
bathrooms, must be avoided under all circumstances.
For safety and approval purposes (CE), you must not rebuild and/or modify this product.
If you use the product for purposes other than those described above, the product may
be damaged. In addition, improper use can cause hazards such as short circuiting,
fire, electric shock etc. Read the instructions carefully and keep them. Make this
product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All
company names and product names are trademarks of their respective owners. All
rights reserved.
Delivery content
• Wireless mouse
• USB receiver
• 2 x AAA battery
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may
become dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong
jolts, high humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can no
longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a
low height can damage the product.
• Also observe the safety and operating instructions of any other devices
which are connected to the product.
• Correct polarity must be observed while inserting the (rechargeable)
batteries.
• (Rechargeable) batteries should be removed from the device if it is not
used for a long period of time to avoid damage through leaking. Leaking
or damaged (rechargeable) batteries might cause acid burns when in
contact with skin, therefore use suitable protective gloves to handle
corrupted (rechargeable) batteries.
• (Rechargeable) batteries must be kept out of reach of children. Do not
leave (rechargeable) batteries lying around, as there is risk, that children
or pets swallow them.
• All (rechargeable) batteries should be replaced at the same time.
Mixing old and new (rechargeable) batteries in the device can lead to
(rechargeable) battery leakage and device damage.
• (Rechargeable) batteries must not be dismantled, short-circuited or
thrown into fire. Never recharge non-rechargeable batteries. There is a
risk of explosion!
• Attention, LED light: Do not look directly into the beam of light! Do not look
into the beam directly or with optical instruments!
• Consult an expert when in doubt about operation, safety or connection of
the device.
• Maintenance, modifications and repairs are to be performed exclusively
by an expert or at a qualified shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Operating elements
Operation
a) Using the 2.4 GHz receiver
1. Remove the wireless receiver labelled "2.4 GHZ" from the receiver dock at the rear
side of the mouse. It has a USB-A connector.
2. Insert it in a free USB port on your computer.
b) Inserting batteries
1. Remove the battery compartment cover on the rear side of the mouse.
2. Insert two Type AAA/Micro batteries with correct polarity into the battery
compartment of the mouse (observe plus/+ and minus/-).
3. Close the battery compartment.
In principle, it is possible to operate the mouse with rechargeable batteries.
Due to lower voltage (rechargeable battery = 1.2V, battery = 1.5V) and lower
capacity of rechargeable batteries, the operating time is shorter than with
batteries. There is also a probability of reduction in radio range. If you wish
to use rechargeable batteries in spite of these limitations, it is imperative
that you use special NiMH rechargeable batteries with low self-discharge.
We recommend that you preferably use high quality alkaline batteries to
ensure long and safe operation.
Replace the batteries every year at least.
c) Connecting the mouse
1. Switch on your computer. After inserting the batteries, the transmitter and receiver
connect automatically using FSK Auto-Link technology. When the connection
is established, the operating system installs the necessary drivers. A pop-up
message confirms successful installation.
2. You can now control your computer by moving the scroll wheel and clicking the
mouse buttons.
The optical sensor on the rear side of the mouse does not operate correctly
on some surfaces, e.g. on glass or shiny, reflective surfaces. In such cases,
use a suitable mouse pad or another surface.
d) 3-stage energy saving function
• The mouse has an energy saving function with 3 stages. If the mouse is not activated
for approx. 12 seconds, it switches to energy saving mode with a current flow of up
to 0.38 mA. This drops to 0.25 mA after 30 seconds. After 8 minutes of no activity, the
LED switches off and the current flow drops to 160 µA. To wake up the mouse, press
any button or move the scroll wheel.
• The mouse switches off if a transmission signal is no longer received. If necessary,
remove the 2.4 GHz receiver to use this energy saving function. Insert it in the
receiver dock on the rear side of the mouse as the receiver is very small and can
be easily lost.