Walther 3-9x40 Kurzanleitung Seite 2

Operation instructions
Your Walther telescopic sight 3-9x40 which you have now acquired is a
highly precise optical instrument. Make sure that you adhere to the
following instructions and you will enjoy a long service life of your
scope.
1. ocular
2. fastening ring
3. magnification adjustment
4
3
2
1
7
Focusing
For focusing loosen the fastening ring.
Focusing of the image is by turning the ocular (the part of the scope
you look into with the eye). After focusing tighten the fastening ring.
It is recommended to adjust this setting at the largest possible magnifi-
cation of 12x as the image will then remain distinct over the entire
range of magnification. Keep an eye relief of approx. 8 to 10 cm (3 to 4
inches) and look through the scope. Only then will you benefit from the
full field of view.
Reticle
The scope has a reticle No. 8. The size of the reticle remains
the same over the entire range of adjustment.
Adjustment of the reticle
Adjustment of the scope on order to correct deviations of the point of
impact is by means of the elevation adjustment (on top of the tube) and
the windage adjustment (on the right side of the tube). To do so, the
dust protection caps have to be removed, then a coin can be used to
turn the appropriate adjustment screw. To facilitate the adjustments, all
screws have a click-adjustment. 1 click changes the point of impact by
.25 inches on 100 yards (7 mm on 100 m). To change the adjustment,
proceed as follows:
Telescopic sight 3-9 x 40
reticle 8
• if point of impact is too low, turn upper adjustment screw towards
"UP"
• if point of impacts is too far right, turn side-mounted adjustment
screw towards "L"
If point of impact is too high or too far left, turn the adjustment screws
5
accordingly. After these adjustments, the protective caps are to be put
back on in order to prevent the penetration of dampness or dirt. The
reticle ist centrally adjusted, it always remains in the centre of the image
during all adjustments.
6
Variable magnification
The setting ring situated in front of the ocular lens is used to set the
4. elevation adjustment
continuously adjustable magnification from 4-fold to 12-fold. The num-
5. tube
ber opposite the marking dot shows the set magnification.
6. objective lens
7. windage adjustment
Care and maintenance
Your Walther telescoping sight does not require any special maintenan-
ce. Do not simply wipe coarse dirt particles (such as sand) off the lenses
but blow it away or use a fine brush to remove it. The simplest way to
clean lenses is to breathe at them and then softly wipe them down with
a clean optical cloth. The blued metal parts should be given the same
treatment as other blued parts of the weapon. Use a cloth slightly dam-
pened with gun oil if required.
After shooting, the dust protection caps should be replaced.
Technical data
magnification:
tube diameter:
objective lens diameter:
reticle:
field of view on 100 m:
3-fold magnification
9-fold magnification
weight including mount:
length:
Accessories:
Dust protection caps, lithium battery 3V CR 2032,
Operation instructions, HighPower mount
3-fold to 9-fold
30 mm
40 mm
8
12,0 m on 100 m
4,5 m on 100 m
515 g
305 mm
Mounting
Prior to the mounting of the telescope sight, the following measures
have to be taken:
-Check your weapon, it must be unloaded.
-Always hold the muzzle of your gun in a safe direction so that an
unintentional discharge cannot cause any damage.
The telescopic sight in its as delivered condition is already fitted with
two mounting blocks which can be used for standard picatinny rails.
First loosen the 8 screws which hold the mounting blocks on the
tube until the blocks can be freely moved. Now loosen the knurled
screws on the mounting blocks, the retaining claw will now open.
Place the blocks on the rail and tighten the knurled screws. Adjust
the telescopic sight in a way that the elevation adjustment turret is
at a right angle and make sure the eye relief is approx.
3-4 " (8-10 cm) with the gun mounted. Now tighten the 8 screws
on the mounting been fired, the knurled screws should be
retightened.
GB
Service:
Sportwaffen GmbH & Co KG
Donnerfeld 2
D - 59757 Arnsberg / Germany
Telefon +49 2932 / 638-241 • Telefax +49 2932 / 638-249
Internet: www.umarex.com • e-mail: sales@umarex.de
04.05 2.1517