Batteries; Surf Elim - Macleanenergy MCE930 Bedienungsanleitung

2.1 Assembly is easy and requires no tools:
1. Open the packing, and take out all parts.
2. Join the search coil and the lower stem (fiberglass-made,
in black color), then tighten the bolt
3. Press the silver button on the upper end of the lower stem,
and slide the lower stem into the upper stem. Adjust the stem
to a length that you feel comfortable when you stand upright
with the detector in your hand, and the search coil is level with
the ground with your arm relaxed at your side. Then counter-
clockwise rotate to tighten the lock cam.
4. Wind the search coil cable around the stem. Insert the
search coil's plug into the search coil jack on the detector's
control housing.
Caution: Do not over-tighten the search coil or use tools such
as pliers to tighten it.The search coil's plug fits into the
connector only in one way. Do not force the plug and also do
not pull on the cable or you could damage it.
5. Assembly the arm support: Press the silver button on the
upper end of the stem and insert the aluminum end of the arm
support. Make sure the silver button pop up physically.
Adjusting the arm support
Standard position of the arm rest usually is comfortable for
most people. Very large forearms and short forearms
(particularly children's arms), can be accommodated by
adjusting the arm rest accordingly. The arm rest is adjustable
to three positions. To adjust, remove the screw from the
underside, then move the arm rest to one of the alternate
positions and re-install the screw.
-09-

2.2 BATTERIES

Caution: This metal detector uses two 9-Volt alkaline
batteries (not supplied). Using only fresh and proper alkaline
batteries is recommended. Do not mix the old and new
batteries or different types of batteries.
Installation:
1. Be sure the power switch is at off-position.
2. Slide the battery cover off in the direction of the arrow.
3. Take out two battery connectors from the compartment.
4. Join the battery polarities with the connectors.
5. Re-install the battery cover.
Warning: Dispose of old batteries promptly and properly, do
not bury or burn the batteries.
Note: If you don't plan to use the unit for a week or more
time, remove the batteries. Batteries can leak chemicals that
can destroy electronic parts. To extend the battery lift,
exchange the left and right battery after 3-4hours of
operation. LOW BATT will display on bottom right corner of
the LCD, it's the time to change the batteries.
3. CONTROL PANEL
DISC/NOTCH
Range
Target
Indicator
Operating
mode
Status Indicator SENS Indicator Depth Indicator
3.1 LCD Indicators
• OPERATING MODE INDICATOR: shows current operating
mode, among the 4 operating modes the detector has:
DISC,ALL METAL, NOTCH, AUTO-NOTCH.
• STATUS INDICATOR: shows current machine status
(SENS adjustment, DISC range adjustment or NOTCH range
adjustment),
• SURF-ELIM selected or not, and low-battery or not.
• Sensitivity Indicator(SENS): indicates current sensitivity
degree of the machine.
• Depth Indicator: shows target depth
• DISC/NOTCH Range Indicator: indicating current
DISC/NOTCH range settings.
• Target Indicator: shows the target category
3.2 CONTROLLERS' QUICK INTRODUCTIONS
(Details see -> BASIC OPERATION)
1. MODE - interchanging the operating mode.
2. ADJUST + – ENTER - adjusting the sensitivity,
DISC or NOTCH range.
3. SURF ELIM - turning the detector into surface
elimination mode.
4. GND TRAC,GND BAL - setting ground balance in ALL
METAL mode and pinpointing a target.
5. VOL controller - power switch of the metal detector, also
used for controlling the detector's volume .
4. BASIC OPERATION
4. Motion and Non-motion Modes
1. ALL METAL Mode is a non-motion mode: In this mode,
metal is detected with the coil motionless over the ground,
and the detector emits only a monotone sound — No need
to move the coil from side to side. In ALL METAL Mode, adjust
GND BAL controller and then press GND TRAC several times to
eliminate ordinary minerals and ores. Metal detector sounds
in middle tone to all targets detected in ALL METAL mode.
2. DISC,NOTCH and AUTO-NOTCH Modes are motion modes:
There're 3 tones to identify different metals in these modes.
Detector can work in auto-ground balance. Sensitivity is
adjustable – while GND BAL is useless in this mode. To reject
the trash metal, you may adjust DISC or NOTCH range. Motion
mode means the coil must be in continuous motion, otherwise
target cannot be detected.
4.2 Power On. Clockwise rotate the VOL knob from off-
position to power on the detector. The machine runs a self-
test first (All display segments will illuminate, and the
detector sounds high, medium and low tones respectively)
then stays in DISC mode after 2-3seconds.
4.3 Four Operating Modes
Interchange among 4 operating modes: DISC, ALL METAL,
AUTO-NOTCH, NOTCH. Press MODE touch pad to change the
operating modes in following order: DISC > ALL METAL >
AUTO-NOTCH > NOTCH > DISC......The operating mode
displays at bottom left corner of the LCD.
1. DISC mode - Power up the machine, and it enters into DISC
mode automatically. In addition, the PROBABLE depth of coin-
sized objects is indicated by the rectangular segment
indicators on the left side of the display. All detected objects
will cause the depth indicator to illuminate. The depth
indication is not accurate for larger objects. In this mode, the
detector can eliminate unwanted objects from detection
among the categories on top of the panel from left to right.
DISC/NOTCH indicator shows detector's current discrimination
level, and an object's probable identification is indicated by the
arrows at the top of the display. SENS shows current sensitivity
level. While DEPTH read the estimated target depth. Each time
a target detected, DEPTH indicator will illuminate. DEPTH
indicator is more accurate in relative depth, the larger the
reading is, the farther the target away from the coil.
Adjusting Target DISC Range: Press ADJ to enter the
machine into DISC range setting status (LCD displays
"DISC/NOTCH" at bottom right corner), then press + to
increase the level of discrimination, and press "-" to decrease
the level of discrimination.
2. ALL METAL Mode - Press MODE pad to enter into ALL
METAL mode, the detector now is in non-motion mode. In this
mode, the machine emits only a monotone sound when
finding a target, and DEPTH indicates relative target signal
strength. The stronger the signal is, the louder the tone is.
Pinpoint is used to locate a coin-sized object precisely. To move
the coil above or near the target area, target will be found
soon. Please make sure the detector is well ground balanced
before using ALL METAL mode. (Please refer to Ground
Balancing and PINPOINTING at Non-motion mode )
Target identification is useless in ALL METAL mode. To see
target identification and depth, please change the detector
into relative motion mode.
-10-