Stage Line TXS-140SET Bedienungsanleitung Seite 7

Please unfold page 3. Then you can always see the
operating elements and connections described.
1 Operating Elements and Connections
1.1 Receiver
1 POWER LED
2 Reception LEDs A + B
3 Overdrive indicator AF PEAK [independent of
volume control AUX VOLUME (8)]
4 POWER switch
5 12 V Power SUPPLY via plug-in power supply
unit (included in the delivery)
6 Anntennas
7 Control SQUELCH for adjusting the muting threshold
8 Volume control AUX VOLUME for the output level
of the jack AUX (9)
9 Output AUX (6.3 jack, unbal.) for connecting an
amplifier or a mixer with unbalanced input
10 Output BAL. MIC (XLR connection, bal.) for connec-
ting an amplifier or a mixer with balanced input
1.2 Microphone with integrated transmitter
11 Screw cap
12 Battery compartment for a 9 V battery
13 Power switch
lower position: Off
medium position: Mute
upper position: On
14 Power LED
2 Safety Notes
These appliances (microphone, receiver, plug-in power
supply) correspond to the directive 89/336/EEC for
electromagnetic compatibility. Additionally, the plug-in
power supply corresponds to the low voltage directive
73/23/EEC.
The plug-in power supply uses lethal mains voltage
(230 V~). In order to prevent a shock hazard, do not
open the plug-in power supply. Leave servicing to
authorized, skilled personnel only. Moreover, any
guarantee expires if one of the units has been opened.
For operation also observe in any case the following:
The units are only suitable for indoor use.
Protect the units against humidity and heat (permis-
sible ambient temperature range 0–40 °C).
Even if the receiver is switched off, the plug-in power
supply has a low power consumption.
Do not set the receiver to operation and immediately
disconnect the plug-in power supply from the mains if:
1. damage at the plug-in power supply or the recei-
ver is visible,
2. a defect might have occurred after a drop or simi-
lar accident,
3. there are malfunctions.
The units must be repaired in any case by author-
ized personnel.
If the units are used for purposes other than orig-
inally intended, if they are operated in the wrong way
or not repaired by authorized, skilled personnel,
there is no liability for possible damage.
For cleaning only use a dry, soft cloth, by no means
chemicals or water.
If the units are to be put out of operation definitively,
bring them to a local recycling plant for disposal.
3 Applications
The wireless microphone system consists of a micro-
phone with integrated, battery-operated transmitter
and antenna, the corresponding receiver as well as a
plug-in power supply. This system enables music and
speech transmission from the microphone to the re-
ceiver. The operating range is approx. 30 m and
depends on local conditions.
The microphone system is available for three diffe-
rent transmission channels:
TXS-140SET 175.00 MHz colour code red
TXS-142SET 195.25 MHz colour code green
TXS-143SET 197.10 MHz colour code yellow
Thus three audio signals can be transmitted when
using three models. Due to the colour code it can
easily be recognized which microphone cooperates
with the respective receiver.
4 Compulsory Registration
With the purchase of this unit you have acquired the
type examination certificate of the Reg TP (Regulie-
rungsbehörde für Telekommunikation und Post = Ger-
man Regulating Authority for Telecommunication and
Post). The BZT number for the microphone is
A130 654J RF.
Despite this, the user is obliged to apply for a fre-
quency allotment at the local branch office of the
Reg TP in the region where the product will be used.
The type examination certificate does not entitle the
user to operate the unit without frequency allotment.
The map on page 9 displays the local branch offices.
The addresses are listed on page 10, an application
form for the frequency allotment is inserted on page 11
and 12. In case of failure to comply with the compul-
sory registration the telecommunication licence regula-
tions will be violated.
The BZT numbers are only valid for the Federal
Republic of Germany! In other countries a respective
approval must be applied for.
5 Power Supply
5.1 Microphone
1) Screw off the screw cap (11) at the lower end of the
microphone.
2) Insert a 9 V battery with the positive and negative
connections as printed in the battery compartment
(12). Tightly screw the screw cap (11) again.
3) With a new battery the microphone can be operated
for approx. 6–8 hours.
4) If not used for a longer period of time (e. g. for more
than one week), the battery should be taken out of
microphone. Thus the microphone will not be
damaged in case the battery should leak.
GB
7