Outdoor Station - easy2wire VDB-6170 Betriebsanleitung

Connecting the radio extension module VTX-BELL
The VTX-BELL can be used to transfer the bell signal by radio to the
recipient of the BELL series (currently BELL 200 RX, BELL 210 USB and
BELL 220 RX). The radio module is attached to the 3-pole plug (B.18)
inside the indoor station. You need the short 3-pole extension that is
included in the VTX-BELL.
IMPORTANT: Please only connect the mains power supply to the
power once the system has been fully mounted. Otherwise short-
circuiting can occur during installation, which can destroy the apparatus
in the worst case.
NOTE: The outdoor station is splash proof in accordance with IP 44. In
heavy rain, particularly in conjunction with high winds, it is still possible
for water to penetrate the casing. We therefore recommend only
mounting the station in a protected outdoor area. If it is not possible to
mount the station in a protected indoor area then weather protection
should be fitted over the outdoor station.

OUTDOOR STATION

Preparation
Please make sure that the nameplates do not fall out when you remove
the front cover as this could damage them.
The camera should be mounted at a height of approx. 1.5 m - 1.6 m
(middle of the camera).
1. Remove both lower screws (A.5) using a suitable screwdriver
(Torx T10).
2. Hold the bottom of the front cover with your thumb and index
finger and pull it forwards slightly. Then lift it upwards slightly.
Make sure that you do not rip off the microphone cable. The
microphone cable is connected to the electronics with a plug and
can be separated easily by pulling it out.
3. Remove the terminal cover by removing both screws (A.6) and then
removing the terminal cover.
4. Look for a suitable place to mount the outdoor unit and lay all the
necessary wires to this location.
Note: Please ensure that the wall at the mounting location is straight
and level.
5. Use the casing to draw the mounting holes on the wall. A spirit le-
vel is useful to check that the outdoor station is mounted straight.
6. Drill the 4 holes that you have drawn with a 6 mm drill and insert
one of the included dowels into each hole.
7. Feed the connection wire through the wire feed and screw the back
part of the casing to the wall.
8. Connect the wire that you have laid to the terminal.
Adjusting the nameplate
The nameplate comprises two transparent plastic parts that are
connected with 2 small screws.
9. Remove both screws and take the nameplate apart. The foil for
inscription is between the two plastic parts.
10. Write on the foil with a smear-resistant felt pen or print a
nameplate* using a PC and printer (you can use normal paper but
printable foil from stationery shop is better suited).
11. Place the inscribed nameplate (foil) between the two plastic parts
and screw them back together.
*Size of the nameplate:
VDB-6170: 71 mm x 34 mm
VDB-6270: 71 mm x 15 mm
12. Insert the nameplates into the outdoor station and fix with a strip
of sticky tape.
13. Insert the microphone cable back into the socket and replace
the front cover onto the outdoor station from above and at an
angle. Please ensure you do not crush the microphone cable. The
projections on the back cover must fit into the notches on the front
cover.
14. Then slide the front cover carefully over the outdoor station and
screw the two fixing screws (A.5) back into the casing.
ASSEMBLY OF THE INDOOR STATION
You can select the mounting height for the indoor station according to
your circumstances.
1. The casing on the indoor station is screwed together with two
screws (B.17) and is kept together with projections and notches.
To separate the back section from the front section remove both
screws and the back section can then be simply removed.
2. Use the back section of the casing as an aid to draw the drill holes.
Make sure that you place the back section in a straight line.
3. Drill the mounting holes with a 6 mm drill and insert one dowel
into each hole.
4. Feed the wires through the correct insertion hole in the back
section of the casing and screw this.
5. Connect the wires in accordance with the wiring plan and place the
front casing section on the back casing section. Make sure that it
clicks into place correctly.
6. Screw the casing back together with the two screws (B.17).
13 13
ENGLISH | easy2wire VDB
GB