Troubleshooting - Skywalker hobbywing Bedienungsanleitung

Trouble Shooting
Trouble
After power on, motor does not work, no
sound is emitted
After power on, motor does not work,
such an alert tone is emitted:
"beep-beep-, beep-beep-,beep-beep-"
(Every "beep-beep-" has a time interval
of about 1 second)
After power on, motor does not work,
such an alert tone is emitted:
"beep-, beep-, beep- "(Every "beep-" has
a time interval of about 2 seconds)
After power on, motor does not work,
such an alert tone is emitted:
"beep-, beep-, beep-" (Every "beep-" has
a time interval of about 0.25 second)
After power on, motor does not work, a
special tone " " is emitted after 2
beep tone (beep-beep-)
The motor runs in the opposite direction
Program the ESC with your transmitter (4 Steps):
Note: Please make sure the throttle curve is set to 0 when the
throttle stick is at bottom position and 100% for the top position.
1. Enter program mode
2. Select programmable items
3. Set item's value (Programmable value)
4. Exit program mode
1. Enter program mode
1) Switch on transmitter, move throttle stick to top
position, connect the battery pack to ESC
2) Wait for 2 seconds, the motor should emit
special tone like "beep-beep-"
3) Wait for another 5 seconds, special tone like
" " should be emitted, which means
program mode is entered
3. Set item value (Programmable value):
You will hear several tones in loop. Set the value matching to a tone by moving throttle stick
to top when you hear the tone, then a special tone "
and saved. (Keeping the throttle stick at top, you will go back to Step 2 and you can select
other items; or moving the stick to bottom within 2 seconds will exit program mode directly)
Tones
"beep-"
Items
1 short tone
Brake
Battery type
Cutoff mode Soft-Cut
Cutoff threshold
Start mode Normal
Timing
www.hobbywing.net
Possible Reason
The connection between battery
pack and ESC is not correct
Input voltage is abnormal, too high
or too low.
Throttle signal is irregular
The throttle stick is not in the
bottom (lowest) position
Direction of the throttle channel is
reversed, so the ESC has entered
the program mode
The connection between ESC and
the motor need to be changed.
"beep-beep-"
2 short tones
Off On
Lipo NiMH
Cut-Off
Low Medium
Soft
Low Medium
Check the power connection.
Replace the connector.
Check the voltage of battery pack
Check the receiver and transmitter
Check the cable of throttle channel
Move the throttle stick to bottom position
Set the direction of throttle channel correctly
Swap any two wire connections between ESC and
motor
2. Select programmable items:
After entering program mode, you will hear 8 tones in a loop with
the following sequence. If you move the throttle stick to bottom
within 3 seconds after one kind of tones, this item will be selected.
1. "beep"
2. "beep-beep-"
3. "beep-beep-beep-"
4. "beep-beep-beep-beep-" cutoff threshold
5. "beep-----"
6. "beep-----beep-"
7. "beep-----beep-beep-"
8. "beep-----beep-----"
Note: 1 long "beep-----" = 5 short "beep-"
" emits, means the value is set
"beep-beep-beep"
3 short tones
High
Super soft
High
Action
brake (1 short tone)
battery type (2 short tone)
cutoff mode (3 short tone)
(4 short tone)
startup mode (1 long tone)
timing (1 long 1 short)
set all to default (1 long 2 short)
e xi t ( 2 l o n g t o n e )
4. Exit program mode
There are 2 ways to exit
program mode:
2. In step 3, after special
tone " ", please
move throttle stick to
the bottom position
within 2 seconds.
3.
In step 2, after tone
"beep-----beep-----"(ie.
The item #8), move
throttle stick to bottom
within 3 seconds.
-
Seite 7