Aufgrund fortlaufender Weiterentwicklungen ist es möglich, dass die in diesem Benutzerhandbuch enthaltenen Hinweise und Informationen nicht vollständig dem Auslieferungszustand des Geräts ent- sprechen. LIEFERUMFANG 1 x QE80.4 DSP Verstärker 1 x Fernbedienung mit LED-Display inkl. Verbindungskabel 1 x USB-Kabel, A- auf Mini-B-Stecker, 5 m 1 x Kabelsatz Hochpegel-Audioeingänge 1 x Kabelsatz Niedrigpegel-Audioausgänge mit 4 Cinch/RCA Buchsen...
SICHERHEITSHINWEISE BITTE BEACHTEN SIE DIE FOLGENDEN HINWEISE VOR INBETRIEBNAHME! DAS VON IHNEN ERWORBENE GERÄT IST NUR FÜR DEN BETRIEB DAS GERÄT NICHT AN STELLEN EINBAUEN, AN DENEN ES HOHER AN EINEM 12-V-BORDNETZ EINES FAHRZEUGS AUSGELEGT. An- FEUCHTIGKEIT ODER STAUB AUSGESETZT IST. Bauen Sie das Ge- dernfalls besteht Feuergefahr, die Gefahr eines elektrischen Schlages oder rät so ein, dass es vor hoher Feuchtigkeit und Staub geschützt ist.
INSTALLATIONSHINWEISE HINWEIS Bevor Sie mit der Installation des Soundsystems beginnen, trennen Sie unbedingt den Massepol der Fahrzeugbatterie ab, um Kurzschlüsse und Stromschläge zu vermeiden. MECHANISCHE INSTALLATION Achten Sie bei der Installation darauf, dass keine serienmäßig im KFZ vorhandenen Teile wie z.B. Kabel, Bordcomputer, Sicherheitsgur- te, Tank oder ähnliche Teile beschädigt bzw.entfernt werden.
SUB L SUB L PRT. PRT. – – – – POW. POW. LINE OUTPUT LINE OUTPUT QE80.4 DSP QE80.4 DSP AUX IN AUX IN PC CONNECT PC CONNECT OFF ON +12V +12V AUTO TURN ON SUB R SUB R OPTICAL INPUT...
G F E – – – – SUB L PRT. – – POW. LINE OUTPUT QE80.4 DSP PC CONNECT AUX IN OFF ON +12V AUTO TURN ON SUB R OPTICAL INPUT ONLY WITH HIGH LEVEL INPUT HIGH LEVEL INPUT WiFi BOX...
FUNKTIONSHINWEISE BELEGUNG KABELSATZ HOCHPEGEL-AUDIOEINGÄNGE BRAUN/SCHWARZ SUB R – 9 11 BRAUN SUB R + ORANGE/SCHWARZ SUB L – 8 10 12 ORANGE SUB L + LILA/SCHWARZ REAR R – LILA REAR R + GRÜN REAR L + GRÜN/SCHWARZ REAR L – GRAU FRONT R + 10) GRAU/SCHWARZ...
Verbinden starten Sie das Programm auf dem Computer. Nach dem Programmstart erscheint die Startmaske. Wählen Sie rechts unten unter Select Device Ihr Gerät QE80.4 DSP mit der Maus aus. Demo-Modus (OffLine-Mode) Sie können X-CONTROL auch ohne Verbindung mit dem DSP-Prozessor im Offline-Modus starten und sich mit den Funktionen der Software vertraut machen.
Seite 9
FUNKTIONSHINWEISE Wurde der Test erfolgreich durchgeführt erscheinen 4 Häkchen in den Checkboxen. Drücken Sie dann auf [OK] Click here to start um fortzufahren. Sollte eines der Häkchen bei einer Checkbox nicht erscheinen, liegt ein Problem vor welches zu einer Fehlfunktion führen kann. Beachten Sie dazu die Angaben im Kapitel Fehlerbehe- bung.
FUNKTIONSHINWEISE BEDIENOBERFLÄCHE DER SOFTWARE Hier können Sie unzählige Einstellungen vornehmen und an Ihr Soundsystem anpassen, welche in Echtzeit über den DSP-Prozessor so- fort hörbar sind. Sobald Sie mit der Konfiguration eines Settings fertig sind, kann dieses auf den einen Speicherplatz im DSP-Prozessor übertragen werden.
Seite 11
FUNKTIONSHINWEISE 2. SOURCE: • Hier wählen Sie zwischen den einzelnen Eingangsquellen OPTICAL (Optischer Eingang), MAIN (RCA/Cinch Audioeingänge) bzw. HI LEVEL (Hochpegel-Audioeingänge), AUX (3,5 mm Klinke Stereoeingang) sowie WiFi (optional). 3. CH-SETTING: • Hier wählen Sie den jeweiligen Ausgangskanal bzw. das Ausgangskanalpaar aus, bei welchem Sie die Einstellungen verändern möchten.
G F E – – – – SUB L PRT. – – POW. LINE OUTPUT QE80.4 DSP PC CONNECT AUX IN OFF ON +12V AUTO TURN ON SUB R OPTICAL INPUT ONLY WITH HIGH LEVEL INPUT HIGH LEVEL INPUT WiFi BOX...
Seite 13
FUNKTIONSHINWEISE KONFIGURATION DER FRONT-KANÄLE 1. Wählen Sie unter SOURCE die Einstellung MAIN. 2. Wählen Sie das Kanalpaar A & B (FL/FR) unter CH SETTING aus indem Sie auf das Schlosssymbol klicken. 3. Wählen Sie unter CROSSOVER > FILTER TYPE die Einstellung HP (Hochpassfilter) 4.
Seite 14
FUNKTIONSHINWEISE ANPASSUNG DER LAUTSTÄRKEPEGEL Passen Sie die Pegel der einzelnen Kanäle nach Ihren Wünschen passend zu den Audiokomponenten und Gegebenheiten im Fahr- zeuginneren an. Beachten Sie hierzu folgende Hinweise: • Senken Sie die Ausgangslautstärke unter MAIN auf -10dB ab um Verzerrungen zu vermeiden. •...
FUNKTIONSHINWEISE ÜBERSICHT DER MÖGLICHEN ANSCHLUSSBEISPIELE Neben dem auf den vorangegangenen Seiten ausführlich beschriebenen Anschlussbeispiel bietet der DSP-Verstärker viele weitere Systemkonfigurationen. Die drei häufigsten sind hier in Kurzform beschrieben: Kanäle Beispiel 1 Beispiel 2 Beispiel 3 Front / Rear mit Front 2-Wege Aktiv-System Front mit Vollbereichslautsprechern Vollbereichslautsprechern Rear mit Vollbereichslautsprechern Rear mit Kickbässen Separater Subwoofer-Verstärker Separater Subwoofer-Verstärker...
PRAXISTIPP: LAUFZEITKORREKTUR Wie stelle ich in der DSP-Software den richtigen Abstand der Laufzeitkorrektur ein, um alle Lautsprecher des Soundsystems aufeinander einzustellen und der Schall gleichzeitig beim Hörer ankommt? Messen Sie zuerst den Abstand der Lautsprecher zur akustischen Bühnenmitte. In diesem Fall ist diese der Fahrersitz auf Höhe der Ohren.
ALLGEMEINE HINWEISE TECHNISCHE DATEN MODELL QE80.4 DSP KANÄLE SCHALTUNGSPRINZIP CLASS D Digital AUSGANGSLEISTUNG RMS 13,8 V Watt an 4 / 2 Ohm 4 x 80 / 125 Watt an 4 Ohm gebrückt 2 x 250 AUSGANGSLEISTUNG MAX. 13,8 V Watt an 4 / 2 Ohm 4 x 160 / 250 Watt an 4 Ohm gebrückt...
FEHLERBEHEBUNG Fehler: keine Funktion Ursache: Lösung: 1. Die Stromversorgungskabel sind nicht korrekt angeschlossen. Erneute Überprüfung 2. Die Kabel haben keinen elektrischen und mechanischen Kontakt. Erneute Überprüfung 3. Die Remote-Steuerleitung des Steuergeräts (Autoradio) ist nicht korrekt am Verstärker angeschlossen. Erneute Überprüfung 4.
Seite 19
FEHLERBEHEBUNG Fehler: kein Ton vom Subwoofer Ursache: Lösung: 1. Die Lautstärke des Subwoofer-Ausgangs (Kanal G/H bzw. SUB OUT) ist an der Fernbedienung zu leise eingestellt. Regler der Fernbedienung drücken und halten, Lautstärke erhöhen wie auf Seite. 7 beschrieben. Fehler: „ERROR“-Meldung bei Verbindung zwischen DSP-Gerät und Computer Ursache: Lösung: 1.
Seite 20
FEHLERBEHEBUNG STÖRUNGEN / INTERFERENZEN Die Ursache von Interferenzen sind meist immer die verlegten Kabel. Besonders anfällig dafür sind die Strom- und Cinchkabel des Sound Systems. Oftmals werden Interferenzen durch Generatoren (Lichtmaschine) oder andere elektronische Steuergeräte des KFZ (Benzinpumpe, Klimaanlage etc.) verursacht. Die meisten dieser Probleme können durch korrektes und sorgfältiges Verkabeln vermie- den werden.
Seite 22
TABLE OF CONTENT SAFETY INSTRUCTIONS INSTALLATION INSTRUCTIONS Mechanical installation ........................24 Electrical interconnection.........................25 FUNCTIONAL INSTRUCTIONS Features and operational controls ....................26 Installation of the DSP software ......................28 Amplifier configuration with the software ..................28 User Interface of the software ......................30 Interconnection example .........................32 Overview of the possible interconnection examples................35 Practice hint: Time Delay .........................36 GENERAL NOTES...
SAFETY INSTRUCTIONS PLEASE NOTE THE FOLLOWING ADVICE BEFORE THE FIRST OPERATION! THE PURCHASED DEVICE IS ONLY SUITABLE FOR AN OPERATION DO NOT INSTALL THE DEVICE AT LOCATIONS, WHERE IT WILL BE WITH A 12V ON-BOARD ELECTRICAL SYSTEM OF A VEHICLE. Other- EXPOSED TO HIGH HUMIDITY AND DUST.
INSTALLATION INSTRUCTIONS NOTE Before you start with the installation of the sound system, disconnect necessarily the GROUND connection wire from the battery to avoid any risk of electric shocks and short circuits. MECHANICAL INSTALLATION Avoid any damages on the components of the vehicle like air bags, cables, board computer, seat belts, gas tank or the like. Ensure that the choosen location provides a sufficient air circulation for the processor.
SUB L SUB L PRT. PRT. – – – – POW. POW. LINE OUTPUT LINE OUTPUT QE80.4 DSP QE80.4 DSP AUX IN AUX IN PC CONNECT PC CONNECT OFF ON +12V +12V AUTO TURN ON SUB R SUB R OPTICAL INPUT...
G F E – – – – SUB L PRT. – – POW. LINE OUTPUT QE80.4 DSP PC CONNECT AUX IN OFF ON +12V AUTO TURN ON SUB R OPTICAL INPUT ONLY WITH HIGH LEVEL INPUT HIGH LEVEL INPUT WiFi BOX...
Seite 27
FUNCTIONAL INSTRUCTIONS ASSIGNMENT CABLE SET HIGH LEVEL AUDIO INPUTS BROWN/BLACK SUB R – 9 11 BROWN SUB R + ORANGE/BLACK SUB L – 8 10 12 ORANGE SUB L + PURPLE/BLACK REAR R – PURPLE REAR R + GREEN REAR L + GREEN/BLACK REAR L –...
FUNCTIONAL INSTRUCTIONS INSTALLATION OF THE DSP-SOFTWARE The DSP software X-CONTROL is suitable for all computers with a Windows™ operating system newer than XP and a USB port. The installation requires approximately 25 MB of free space. Due to the principle it should be used with a portable laptop computer. First insert the enclosed software CD-ROM into the computer drive or download the DSP software X-CONTROL via the internet link http://www.audiodesign.de/dsp.
Seite 29
FUNCTIONAL INSTRUCTIONS If the test was performed successfully 4 check marks in the check boxes appear. Then press [OK] Click here to start to continue. Should one of the check marks not appear, a problem occurred that can lead to a malfunction. Please refer to the information in the Trouble Shooting section.
FUNCTIONAL INSTRUCTIONS USER INTERFACE OF THE SOFTWARE Here you are able to adjust many settings to customize your sound system, which are immediately audible in real time via the DSP pro- cessor. Once you are done with the configuration of a setting, it can be transferred to a storage space on the DSP processor. You can store up to 10 different settings and select them with the remote control at any time during operation.
Seite 31
FUNCTIONAL INSTRUCTIONS 2. SOURCE: • Here you can choose between the different input sources SPDIF (optical input), MAIN (RCA audio inputs) or HI LEVEL, AUX (RCA stereo input) and WiFi (optional). 3. CH-SETTING: • Here you select the particular output channels or output channel pairs in which you want to change the settings. You have the option to link the respective channel pairs for L and R with the lock symbol in the middle to synchronize the settings for both channels.
G F E – – – – SUB L PRT. – – POW. LINE OUTPUT QE80.4 DSP PC CONNECT AUX IN OFF ON +12V AUTO TURN ON SUB R OPTICAL INPUT ONLY WITH HIGH LEVEL INPUT HIGH LEVEL INPUT WiFi BOX...
Seite 33
FUNCTIONAL INSTRUCTIONS CONFIGURATION OF THE FRONT CHANNELS 1. Choose under SOURCE the setting MAIN. 2. Choose the channel pair A & B (FL/FR) under CH SETTING by clicking on the lock symbol. 3. Choose under CROSSOVER > FILTER TYPE the setting HP (high pass filter) 4.
Seite 34
FUNCTIONAL INSTRUCTIONS ADJUSTING THE VOLUME LEVEL Adjust the volume level according to your needs and the audio components and characteristics of your vehicle‘s acoustic. Please note the following information: • Slide down the main volume under MAIN to -10dB to avoid distortions. •...
FUNCTIONAL INSTRUCTIONS OVERVIEW OF POSSIBLE INTERCONNECTION EXAMPLES Besides the interconnection example described in detail in the preceding pages the DSP amplifier offers many other system configurations. The three most common are described here in brief: Channels Example 1 Example 2 Example 3 Front / Rear with Front 2-Way Active System Front with Full Range Speakers Full Range Speakers Rear with Full Range Speakers Rear with Kickbasses Separate Subwoofer-Amplifier Separate Subwoofer-Amplifier Separate Subwoofer-Amplifier...
PRACTICAL HINT: TIME DELAY How do I set the correct distance of the time delay function in the DSP software to adjust all speakers of the sound system to each other, that the sound arrives at the listener at the same time? First measure the distance of the speakers to the acoustic center of the stage.
GENERAL NOTES SPECIFICATIONS MODEL QE80.4 DSP CHANNELS CIRCUIT CLASS D Digital OUTPUTPOWER RMS 13,8 V Watts @ 4 / 2 Ohms 4 x 80 / 125 Watts bridged @ 4 Ohms 2 x 250 OUTPUTPOWER MAX. 13,8 V Watts @ 4 / 2 Ohms...
TROUBLE SHOOTING Malfunction: no function Reason: Remedy: 1. The power supply connection of the device is not correct Recheck 2. The cables have no mechanical or electrical contact Recheck 3. The remote turn-on connection from the head unit to the amplifier is not correct Recheck 4.
Seite 39
TROUBLE SHOOTING Malfunction: no subwoofer sound Reason: Remedy: 1. The volume of the subwoofer output (channel G / H and SUB OUT) is set too low on the remote control. Press the remote controller and hold. Turn up the volume. (Refer to page 25).
Seite 40
TROUBLE SHOOTING ELECTRICAL INTERFERENCES The reason for interferences are mostly the routed cables and wires. Especially the power and audio cables (RCA) of your sound system are vulnerable. Often these interferences are caused by electric generators or other electrical units (fuel pump, AC etc.) of the car. The most of these problems can be prevented by a correct and careful wiring.