2 x 9pol D-Sub, Buchse mit Gehäuse 2 x RJ-45 Stecker mit Knickschutztülle Haftung Der Autor sowie die Firma Dallmeier electronic GmbH & Co.KG übernehmen keine Haftung für Schäden aller Art, die durch un- sachgemäßen Gebrauch des Handbuches oder der Tastatur TA- 24 entstehen.
Achten Sie auf die Einhaltung aller angegebenen technischen Kenndaten und Betriebsbedingungen. Der bestimmungsgemäße Betrieb der TA-24 ist nur bei geschlossenem Gehäuse gewähr- leistet. In Verbindung mit der TA-24 dürfen nur die vom Hersteller empfohlenen und geprüften Zubehörteile und Erweiterungs- komponenten eingesetzt werden (CE-Kennzeichen).
Seite 7
Service. Überprüfungen, Einstellungen und Reparaturen Alle Überprüfungen, Einstellungen und Reparaturen die im Inne- ren der TA-24 durchgeführt werden müssen, dürfen nur von ge- schultem und autorisiertem Servicepersonal durchgeführt wer- den. Vor dem Öffnen des Gehäuses muss unbedingt der Netz- stecker gezogen oder das Netzteil von der Spannungsversorgung getrennt werden.
& Verbinden Sie die Tastatur mit dem Rekorder. & Schließen Sie die Geräte wieder an Ihre Spannungs- versorgung an. Anschluss an Rekorder über RS232 Schnittstelle RS 232 COM-Port (Auswahl siehe Kap. 5) Nullmodem-Kabel Dallmeier electronic GmbH & Co.KG...
Tastatur TA-24 Anschluss von 2 Tastaturen über RS232 Hinweis! Beachten Sie bitte, dass beide Com-Ports entsprechend Kapitel 5.1 zu konfigurieren sind! COM-Port 1 COM-Port 2 Dallmeier electronic GmbH & Co.KG...
Der Anschluss der Spannungsversorgung erfolgt über ein exter- nes Netzteil (9-12V DC). Hinweis! Beachten Sie bitte die dem Dallmeier Network Interface DNI- TA24 beiliegende Beschreibung. Das DNI-TA24 kann über Fa. Dallmeier electronic GmbH & Co.KG bezogen werden. Dallmeier electronic GmbH & Co.KG...
Funktion Kontakt. Unabhängig vom Sequenzer- betrieb wird immer dann ein Bild aufgeschaltet, wenn ein kamerabezogener Kontakt ausgelöst wird. Das betreffende Bild bleibt so- lange aufgeschaltet, bis eine andere Kamera per Tasten- druck aufgeschaltet wird. Dallmeier electronic GmbH & Co.KG...
Setup > System > Optionen & Wählen Sie im Feld Tastatur- Mode die Funktion TAC-18 / TA-24. 24 Kameras werden erst ab Rekordersoftware Version 5.0.7 unterstützt. Bei älteren Softwareversion erstreckt sich der Funktionsumfang auf nur 18 Kameras. Dallmeier electronic GmbH & Co.KG...
Tastatur TA-24 Bedienung und Funktion Die volle Funktionalität der TA-24 steht sowohl im Live-Modus als auch im Wiedergabe-Modus des Rekorders zur Verfügung. Wurde am Rekorder eine Spur für Wiedergabe geöffnet, sind nur noch die Tasten zur Spursicherung aktiviert. Eine Kameraum- schaltung mit den Zifferntasten ist in diesem Fall nicht möglich.
Die Zifferntaste (Kameranummer) muss somit innerhalb von 2,5 Sekunden nach dem Drücken von F1 betätigt werden. Wird diese Zeit überschritten, muss erneut F1 und dann die Zifferntaste ge- drückt werden, um die betreffende Standardspur zu sichern. Dallmeier electronic GmbH & Co.KG...
Funktion bei dieser Distanz nicht garantiert) Reichweite RS485: 1000m Spannungsversorgung: 7,5V bis 12V Stromaufnahme: ca. 100mA Gehäuse: Kunststoff Abmessungen: 200 x 150 x 51,5 mm (L x B x H) Gewicht: ~ 600g ohne Netzteil Dallmeier electronic GmbH & Co.KG...
Seite 20
Tastatur TA-24 Dallmeier electronic GmbH & Co.KG...
Seite 21
Connection to the recorder via the RS232 .......... 23 Connection of 2 keyboards via RS232 ..........24 Connection to the recorder via the RS485 .......... 25 Connection TA-24 via DNI-TA24 ............26 Configuration ................. 27 Defining the function of the serial interface ........27 Enabling Event-Controlled Switching ...........
Liability Neither the author nor Dallmeier electronic GmbH will accept any responsibility whatsoever for damage of any kind which may be incurred through the use of this manual or the TA-24 Keyboard. Feature Overview Membrane keyboard with 30 keys 24 camera-assigned keys...
TA-24 (CE conformity seal). Protection against condensation If the TA-24 is brought directly from a cold environment into a warm room, there is a possibility that condensation may form inside the TA-24. Wait approx. 8 hours for the TA-24 to reach room temperature before starting operation.
Seite 25
Incorrect installation and static charging can cause damage to electronic components and result in equipment failure. Non-compliance with or violation of these safety instructions can result in severe equipment failure and either limit its use or render it impossible. Dallmeier electronic GmbH & Co.KG...
Connect the keyboard to the recorder. & Then reconnect the devices to the main power supply. Connection to the recorder via the RS232 Interface RS 232 COM port (see Section 5 for selection) Null modem cable Dallmeier electronic GmbH & Co.KG...
Keypad TA-24 Connection of 2 keyboards via RS232 Attention! Please note that both Com-Ports require configuration as described in Section 5.2! COM-Port 1 COM-Port 2 Dallmeier electronic GmbH & Co.KG...
Please refer to the operating manual for the converter for precise instructions on the wiring and cabling of the RS232/RS485 converter. 2-wire cable (twisted pair) " Interface RS 485 COM port (see Section 5 for RS 485 selection) RS 232 Interface converter Dallmeier electronic GmbH & Co.KG...
9 ...12V COM-Port 1 or 2 The DNI-TA-24 is connected to the recorder using the RS232 cable supplied (1:1 assignment). The two RS485 signal lines from keyboard are connected to the 3-pole screw terminals (T+to Pin1, T-to Pin 2). Alternatively a direct connection can be made using a patch cable (1:1) assignment).
In order to operate the keyboard, the relevant function must be defined on the serial interface. To access Serial Interfaces click Setup > Interfaces > Serial & First select the interface to which the TA-24 keyboard is (to be) connected (A). & In the Function box, select Commanding (B). Settings: Interface: Com port to which the keyboard is connected.
& Select the function Contact in Event-Controlled Switching box. Regardless of sequencer operation, a picture will always be switched when a camera contact is activated. The rele- vant picture will remain displayed, until another camera activated pressing a key. Dallmeier electronic GmbH & Co.KG...
Setup > System > Options & Select the function TAC-18 / TA- 24 in the Keyboard mode box. 24 cameras are supported from recorder version 5.0.7 and higher. Older software versions support only 18 cameras. Dallmeier electronic GmbH & Co.KG...
Keypad TA-24 Operation and function The complete functionality of the TA-24 is available in both the Live and Playback recorder modes. If a track is opened on the recorder for playback, the keys for track- saving alone remain active. Camera switching using the digit keys is not possible in this case.
The digit key (camera number) must be pressed within 2.5 seconds of pressing F1. If this time limit is exceeded, F1 must be pressed again, followed by the digit key, in order to save the rele- vant standard track. Dallmeier electronic GmbH & Co.KG...
(reliable operation not guaranteed at this distance) Range of RS485: 1000m Power supply: 7.5V to 12V Power consumption: approx. 100mA Housing: Plastic Dimensions: 200 x 150 x 51.5 mm (L x W x H) Weight: approx. 600g w/o power supply Dallmeier electronic GmbH & Co.KG...